Welcome to Theoben Rapid Forum. Please login or sign up.

Members
Stats
  • Total Posts: 22,074
  • Total Topics: 3,204
  • Online today: 23
  • Online ever: 1,511 (July 25, 2026, 07:29:23 PM)
Users Online
  • Users: 0
  • Guests: 49
  • Total: 49

Twitter YouTube Facebook

Theoben Rapid Forum

Click above to make a donation. Thank you for supporting The Theoben Rapid Forum.

Reg pressure?

Started by Rapid Dick, December 22, 2021, 04:05:05 PM

Previous topic - Next topic

Rapid Dick

Just ordered a reg for my mk1 and wanted to know whats the recommend pressure setting?? . 22 cal 12ftlb..

TIA..
Old Mk1 Rapid with tasteful updates,
And a couple of BSAs. 😜

KevG

depends whats been done to the mk1 to take the reg.if its a very late mk1 2007 or after its 1200 psi.if its an ebay one thats advertised as mk1 reg they are not actually  for a mk1.
KevG
Like Like x 2 View List
Regards KevG.
Administrator

Mickyd

You should have got one from kevG .md
Like Like x 1 View List

Rapid Dick

 :-\ oh dear... Ebay special.. The block is 1995.. 🙄
Old Mk1 Rapid with tasteful updates,
And a couple of BSAs. 😜

KevG

its my fault rapid dee sent me a pm on the 13th asking about a reg and only just seen it last night.my apologies
KevG
Regards KevG.
Administrator

KevG

sorry mix up it was rapid7bee that messaged me
KevG
Regards KevG.
Administrator

Rapid Dick

Thnx Kev..    So is 1200psi still the pressure to use..?

Cheers..   Ho ho ho   🎅
Old Mk1 Rapid with tasteful updates,
And a couple of BSAs. 😜

Squinty

yeahhh same pressure  ...but the early block isn't ported for a regulator.

The thread blocks the R7/mk1 port between inlet and valve chambers.
Kev's  reg has a waist and hole to line up with the port..

Smaller port for sub-12 fastflow at front...modified with 2nd port for reg.
Can be DIY but one slip and it's buggered.





Like Like x 1 View List

KevG

I set them at 1350 psi if the mk1 is all standard.this gives you around same shot count as a mk2 but slightly better shot to shot consistency. would not realy know what to say for ebay one.if you port action as per mk2 so Ebay reg works at its best I would go 1200 psi.if you just put Ebay reg in to a standard mk1 block performance will be poor.you should still be able to get 12 ftlbs but gun will not be very efficient ie poor shot count.
KevG
Like Like x 1 Disagree Disagree x 1 View List
Regards KevG.
Administrator

Rapid Dick

Thanx you 2 for that info..   I have messed with the ebay one but cant get it anywhere near 1200psi.. How much is yours kev ready to screw in?

Thnx
Old Mk1 Rapid with tasteful updates,
And a couple of BSAs. 😜

KevG

thats strange you should be able to get that pressure easy.i would try doubling up the bellevile washers.like this (())(())(()) as opposed to this()()()()()
KevG
Regards KevG.
Administrator

Rapid Dick

Theres only 7 washers on it Kev..
It came like this () () () ( nut..  I have tried removing a pair and then replaced them like this..  ) () () () nut..  I got it to read 11000 psi briefly but it didnt last before it went back to bottle pressure..  I think the little nylon pip that seals the inlet that aint blocking the inlet flow..   I'm gonna go back to fast flow..

🤔
Old Mk1 Rapid with tasteful updates,
And a couple of BSAs. 😜

Ca_Varminter

Well someone has pulled a few washers off of the Reg...
You need to get KevG to sent a few over...
To configure it to :....(())(())(())
!!

Stuart

Rapid Dick

Theres not enough room to get 12 washers pn it... I said 7 earlier, i wad wrong, there's actually 5.. 😐
Quote from: Ca_Varminter on December 26, 2021, 08:50:18 PM
Well someone has pulled a few washers off of the Reg...
You need to get KevG to sent a few over...
To configure it to :....(())(())(())
!!

Stuart

Old Mk1 Rapid with tasteful updates,
And a couple of BSAs. 😜

KevG

if it crept up to bottle pressure it as creep to or open reg.
KevG
Regards KevG.
Administrator

This website is proudly hosted on Crocweb Cloud Website Hosting.

Crocweb Cloud Website Hosting

Welcome to the Theoben Rapid Forum

© 2026 Theoben Rapid Forum. All rights reserved.