Welcome to Theoben Rapid Forum. Please login or sign up.

Members
Stats
  • Total Posts: 22,074
  • Total Topics: 3,204
  • Online today: 23
  • Online ever: 1,511 (July 25, 2026, 07:29:23 PM)
Users Online
  • Users: 0
  • Guests: 9
  • Total: 9
  • Baidu (2)

Twitter YouTube Facebook

Theoben Rapid Forum

Click above to make a donation. Thank you for supporting The Theoben Rapid Forum.

Losing faith

Started by PiL, September 25, 2021, 11:27:26 AM

Previous topic - Next topic

PiL

Went to take the Rapid mk1 out last night and the cylinder was empty. Should be a two min job as I've got a Best Fittings quick fill, if only  :-[  . It's .177 and I've knocked the pin out to make it fast flow. I've attempted to fill 6 times now by cocking the bolt and   pushing the bolt back and forth trying to open the valve to get pressure behind it but to no avail, air still coming down the barrel.
Am I doing something wrong / is there an  easier way to sort this out?
Seals were changed about a month ago, could there be debris on a valve seal letting air by?
Really want to gel with the Rapid but it's spending more time empty and apart than all the other rifles I own put together  :(
I really don't want to send it off but I'm up and down the country a few times a year and if I can't resolve the problem myself, would there be anyone on here that could help me out?
I'm a patient man but I'm not feeling the love with this rifle and the next step is to sell it off lol

angrybear

If it's leaking down the barrel then it's the exhaust valve, but which part is a different question.
Have you messed with the valve spring? did the body or face get scratched when you removed it, how did you remove it ?
Have you messed with the hammer spring & maybe bent the core ?
Unless it's a registered fac you don't want it FF you want it reg'd, put the pin back in

The bolt doesn't effect the valve, only the hammer does, if it leaks down the barrel sometimes dry firing the empty rifle will make it seat & seal,
but if you missed an O-ring or one got damaged during fitting then it needs doing again.

PiL

Thanks for the reply angrybear, I'll put the pin back to see if it makes a difference. All was OK until a change of job location meant had to leave the Rapid at home for the last 3 weeks. Checked the S510 and the Rapid last night and both empty.
Spanners out again lol lol

Ca_Varminter

Well removing the disk-pin will not have anything to do with your Air rushing out the barrel Problem...

So cocking your rapid is to pull the hammer off the Valve-stem. This allows the valve return spring to
push the valve closed..
Are slow filling it??
Sometime you may need to give a Good shot of High Pressure to get the valve to seal
if your gun is completely Empty!!! Once it seals, fill normally!!

But if that doesn't help you need to check the Valve-Body's large O-ring(s) are good, clean, and not dry..
Nex you need to check the where the valve-stem seals on the valve-body. Make sure it clean, free of defects.
Finally check the Valve-Stem. Roll it on a table to see if it not Bent!!

Here is a photo of the areas to check on the Valve-body...


Good Luck,
Stuart

Squinty

As already said you may need to get more pressure  into the bottle to get a seal, when I fitted a QF to one of mine it took 60-70 bar.


PiL

Quote from: Ca_Varminter on September 25, 2021, 04:43:45 PM
Well removing the disk-pin will not have anything to do with your Air rushing out the barrel Problem...

So cocking your rapid is to pull the hammer off the Valve-stem. This allows the valve return spring to
push the valve closed..
Are slow filling it??
Sometime you may need to give a Good shot of High Pressure to get the valve to seal
if your gun is completely Empty!!! Once it seals, fill normally!!

But if that doesn't help you need to check the Valve-Body's large O-ring(s) are good, clean, and not dry..
Nex you need to check the where the valve-stem seals on the valve-body. Make sure it clean, free of defects.
Finally check the Valve-Stem. Roll it on a table to see if it not Bent!!

Here is a photo of the areas to check on the Valve-body...


Good Luck,
Stuart
For a relative newbie to the Rapid platform, the pics and and info is most welcome Stuart, many thanks
Steve
Like Like x 1 View List

PiL

#6
Quote from: Squinty on September 25, 2021, 04:58:26 PM
As already said you may need to get more pressure  into the bottle to get a seal, when I fitted a QF to one of mine it took 60-70 bar.
Cheers mate, I managed to get it filled the previous time when the bottle was empty but like I said, I had to pull the bolt back and keep twoing and frowing the bolt so the hammer knocks the valve open to get air in behind (I think that's what I was told? ). Next job is to take the valve out and inspect 👍👍
Steve

Just to add, managed to get air behind the valve but it's leaking so I'll inspect the valve  and go from there.
Thanks to all who have commented and pointed me in the right direction , cheers lads 👍
Steve

PiL

Well bowl me over with a feather duster, only gone and filled the Rapid. The test is now that it doesn't leak!! 🤞👍

I had some work done on the Rapid previously from someone who was a member on the old forum who wishes to stay anonymous as I think there was a bit of falling out. I mentioned that forum was no longer and two new one's formed and to maybe take a peek in, but I think it left a bad taste so declined my offer. Its a shame really as like the lathe lads on here and the other place, he really knows his stuff!

Its the first time I have taken the Rapid apart fully, many thanks to you lads who have helped in the advice given. I feel quite confident on changing the seal's if and when it leaks again 👏👍
Like Like x 1 View List

This website is proudly hosted on Crocweb Cloud Website Hosting.

Crocweb Cloud Website Hosting

Welcome to the Theoben Rapid Forum

© 2026 Theoben Rapid Forum. All rights reserved.