Welcome to Theoben Rapid Forum. Please login or sign up.

Members
Stats
  • Total Posts: 22,074
  • Total Topics: 3,204
  • Online today: 23
  • Online ever: 1,511 (July 25, 2026, 07:29:23 PM)
Users Online
  • Users: 0
  • Guests: 5
  • Total: 5
  • Baidu

Twitter YouTube Facebook

Theoben Rapid Forum

Click above to make a donation. Thank you for supporting The Theoben Rapid Forum.

Can anyone explain this product by TR-Rob , " Fast Flow Valve"

Started by Kernal, November 19, 2020, 11:27:34 PM

Previous topic - Next topic

Kernal

Bargain time for the Rapid 7 Stainless Steel bottle holder, bypasses regulator for owners who are having trouble with the standard regulator that may be leaking, inconsistent or low power. Also suitable if your gun is FAC.
On the inter net these are £86.00.
This bottle holder has an adjustable bottle opening, so it can be set to prevent blowing bottle seals if the valve is opening too early.
It has two holes for a clear fast flow through. We have tried them with six holes and there was no noticeable difference, so we kept two for extra strength.

This is the longer one (30mm) that replaces the regulator type of bottle holder. The early mark 1 had a short bottle holder (20 mm) without any regulator.

This longer one will still fit the early mark 1s but the bottle will be approximately 10 mm further forward. Also includes the inner seal already fitted.
The easiest way to adjust is to fill the bottle, unscrew the centre screw actuator (Grub Screw) so it is clear of the bottle ball valve. Then screw the full bottle on to the holder, while the grub screw is clear of the bottle valve. With the bottle now screwed on to the Bottle Holder, it is then a simple matter of screwing the grub screw in gently until it touches the ball valve, BUT DO NOT SCREW ANYMORE OR YOU WILL OPEN THE BOTTLE VALVE AND GET A BLAST OF HP AIR.
Remove the bottle while still holding the grub screw position. The grub screw now needs to be turned in nearly one turn and Locktite at that position. This is about right (although some guns may vary) to just open the bottle ball valve just as the bottle O ring has sealed. If the bottle opens too early then the high pressure air will blow the O ring bottle.
When ever you are doing up the freshly filled bottle, it is always best to do it up smartly at the end so you do not give it time start pushing the Bottle O ring out of the tiny gap.





This comment confuse`s me the most below,

This bottle holder has an adjustable bottle opening, so it can be set to prevent blowing bottle seals if the valve is opening too early.
It has two holes for a clear fast flow through. We have tried them with six holes and there was no noticeable difference, so we kept two for extra strength.


Can anyone explain what he`s talking about as i`m sure this is only a fastflow valve he`s selling here?

:)

dyker2010

it is just a fast flow, this is for mk2,mfr to replace the reg . adjustable bit is for opening the bottle valve, extra holes is on threaded bit standard is two some folk knock out pin gives you four six leaves not much metal left leaving a weak point for strength, a genuine mk2 fast flow is threaded all the way up as port is in different place. so this for a mk1 block which will move the bottle 10mm farther out if on mk1 stock unless its for putting a mk1 block in a mk2 stock????  dont see the point for a mk1block and stock no gain over mk1 bottle holder only your bottle sticks out more

KevG

thats for high power or a .177.that would give bad consistency on a .22 mk1 at sub 12 ftlbs
KevG
Regards KevG.
Administrator

This website is proudly hosted on Crocweb Cloud Website Hosting.

Crocweb Cloud Website Hosting

Welcome to the Theoben Rapid Forum

© 2026 Theoben Rapid Forum. All rights reserved.