Welcome to Theoben Rapid Forum. Please login or sign up.

Members
Stats
  • Total Posts: 22,073
  • Total Topics: 3,204
  • Online today: 23
  • Online ever: 1,511 (July 25, 2026, 07:29:23 PM)
Users Online

Twitter YouTube Facebook

Theoben Rapid Forum

Click above to make a donation. Thank you for supporting The Theoben Rapid Forum.

STX Smooth twist liner

Started by angrybear, April 19, 2025, 08:43:43 PM

Previous topic - Next topic

angrybear

Just got hold of one cheap, with the intention of adapting it to an MFR to try/use slugs.
Someone must have had a go already any hint's tip's welcome.

The current plan is a brass "breech" end & inset the liner just shy of the port, sleeve with carbon for support & then shroud the lot  ???

Ca_Varminter

Yes...
I know few that have made Breech extension the screws into the steel barrel outer sleeve.
It also has the internal O-ring to seal the smooth-twist barrel liner.

Stuart

Dave74

Yes running a few superior liners got it made so the liners can be changed over, liking the 600mm heavy slug version.
Agree Agree x 1 View List
Fit like n !!!

Therapidman

Been there and spent a load of money on them liner making them fit. 500mm might be OK but the 600mm and 700mm are just to bendy even with carbon stiffer... if you want a slug barrel buy a alfa barrel

Therapidman

I have 3 made you could set the gun up shooting perfect put it away getbit out day after and would have changed zero .. there is to much flex in them .. I think that's why the fx have a bad name for them not holding zero

Dave74

Mine holds zero fine  so much different ways to set liners up, been through all that and got there in the end.
Fit like n !!!

DAVYW1

My tensioned liner setup holds zero fine. The liner is permanently attached to a steel breech end, a carbon tube covers the liner and slots into the breech end and then a tensioned metal end with a threaded end is attached to the muzzle end of the liner. When you tension the muzzle nut the liner is tensioned between the two ends and supported by the carbon tube. If i could figure out how to put up pics i'd show you what i mean?!
Agree Agree x 1 View List

Squinty

#7
Been messing about/ mulling over a 500mm/19" .177 Superior liner for quite a while now, my pillar drill went bzzzz-pop last week so haven't got any closer to finishing.
Porting, shroud fixings and splitter to finish still ::)

Was going to make a collet holder affair which didn't turn out as expected... down to 16" now.

Not the ideal route perhaps but I threaded the liner, stainless breech block and alloy splitter  M-7x0.75 and will bond the liner into the breech.
The Cf stiffener is recessed 15mm into the breech block and 10mm into the splitter and even with light tension it still seems that there is some flex although the shroud should hold tight.

KevG

made a couple with great success.they sit in 14mm shower pipe.sturdy as you like with no zero shift problems.
kevG
Agree Agree x 2 View List
Regards KevG.
Administrator

Brooksy

Quote from: KevG on April 22, 2025, 08:59:08 PMmade a couple with great success.they sit in 14mm shower pipe.sturdy as you like with no zero shift problems.
kevG
14mm shower pipe? What's that Kev, the chrome pipe or copper?

KevG

Regards KevG.
Administrator

Brooksy

I see what you mean Kev. 14mm internal diameter, 15 mm outer.

Dave74

The liners are roughly 8.3mm diameter iirc.
Fit like n !!!

Ca_Varminter

Quote from: Dave74 on April 23, 2025, 07:15:01 AMThe liners are roughly 8.3mm diameter iirc.
Depends on Caliber.......

Stuart

Dave74

O ye never thought of that I only been using .22, guess that's why the stiffner tubes are calibre specific
Like Like x 1 View List
Fit like n !!!

This website is proudly hosted on Crocweb Cloud Website Hosting.

Crocweb Cloud Website Hosting

Welcome to the Theoben Rapid Forum

© 2026 Theoben Rapid Forum. All rights reserved.