Welcome to Theoben Rapid Forum. Please login or sign up.

Members
Stats
  • Total Posts: 22,074
  • Total Topics: 3,204
  • Online today: 23
  • Online ever: 1,511 (July 25, 2026, 07:29:23 PM)
Users Online
  • Users: 0
  • Guests: 46
  • Total: 46

Twitter YouTube Facebook

Theoben Rapid Forum

Click above to make a donation. Thank you for supporting The Theoben Rapid Forum.

Hammer pip

Started by Andycoup, January 02, 2022, 05:34:28 PM

Previous topic - Next topic

Andycoup

Hi folks, hope you're all enjoying your new year bank holiday weekend.

I recently aquired rapid number 4, which had been 'modded'. The pip has been (quite crudely) shortened.

Is the pip removable from the hammer? And if so, is it threadlocked in?

The gun is a late block, mk4 trigger, if that helps.

Cheers, Andy.

Rapid7bee

Yes,just heat up the top/tip with a blowtorch until you smell the glue/loctite
burning. Unsrew when hot as much easier, I done my last night.
Like Like x 3 Agree Agree x 1 View List

alan1

There should be information about pip leights for sub 12 and fac and people who can supply one

Squinty

there's barely a handful of people who make and supply parts exclusively for Rapids and a few good lathe guys that may come to the rescue if asked.
otherwise take your pick and ask one of the known airgun tuners.... who might make a pip if not too busy.

...even a 2ba bolt (and locknut) the right length will do the job ;)

15-17mm sub-12
6-10mm for the others
Like Like x 1 View List

Andycoup

Making a pip shouldn't be too much of a problem, I have access to a lathe.

I think I measured the length of the pip at 12mm, so it definitely needs lengthening. I'll probably do a silent pip.

Andy.

KevG

between 16 and 17 mm for sub 12ftlbs. 2BA thread length of thread 14mm.this is critical on thread length as you need it to extend slightly into the hammer chamber for the inertia spring to sit on.other wise is will distort and break
KevG
Like Like x 1 Winner Winner x 1 View List
Regards KevG.
Administrator

alan1

Yes I found out the hard way when I made my first pip with a short thread and damaged the spring and did not know at time it was due to that

alan1

Hi do R A W use a hammer with a pip with no thread sticking through

Aggy

The Raw is all one piece not adjustable
Raw HM1000x fac .22
Skout Epoch .25 fac
Beretta 680

Ruger m77 mk2 .223
Many many many others been and gone

KevG

earlier Raws were threaded hammers like the theoben/impacts
KevG
Regards KevG.
Administrator

alan1

So how does the inatia spring not get damaged

KevG

it can do.did one last week what had the one piece hammer and that spring was buckled.
KevG
Regards KevG.
Administrator

KevG

its not just the latest Raws that have the one piece hammers.they were also on the first Airforce ones to.
KevG
Regards KevG.
Administrator

Ca_Varminter

Quote from: alan1 on January 08, 2022, 03:41:05 PM
So how does the inatia spring not get damaged

First WHY it Happens ....
The small Inertia weight uses the threaded potion of the Inertia Weight  as a Spring Guide and Striker!
If there isn't enough of the Threaded Portion Exposed, the Inertia(anti-rattle) Spring will Pound itself into Dust!!

HOW to Prevent this from happening...
1. If you're replacing your Pip.
    Compare the Threaded portions between the old one and New, making it is not too short!!
2.Make sure you apply a little Loctite to the new pip.... It can back out.. Causing the same condition as Above!

Stuart

Aggy

My New spec Raw has a small projection at the inside front of the hammer ,guess it must be either a pressed in piece or machined in ?
Like Like x 1 View List
Raw HM1000x fac .22
Skout Epoch .25 fac
Beretta 680

Ruger m77 mk2 .223
Many many many others been and gone

This website is proudly hosted on Crocweb Cloud Website Hosting.

Crocweb Cloud Website Hosting

Welcome to the Theoben Rapid Forum

© 2026 Theoben Rapid Forum. All rights reserved.