Any member can let me know where to get the correct o rings that for a raw Hm1000x with v quick fill
The O rings that go on both sides of the V fill ?
Thanks
BS017....
Stuart
Hi Stuart
I've checked that out and it shows them as 70 Shore hardness..
I'm lead to believe they should be 90 Shore??
Thanks
Tich
I have been using 80-90 shore hardness.... without any problems..
Stuart
Ok Stuart..Following on from your recommendation..I've ordered a fair few of these,I'm hardly going to use all!
If any members should need any..plz let me know..I'll send them to you.
Tich
BS017 Nitrile 90 O'Ring (50x)
I got a few packs of the oring kits from bagnell and Kirkwood they got the orings for the quick fill
Ok Members..I've had a delivery of a good few o rings for Raw quick fill kits.
If anyone needs any just let me have your address and I'll post them f.o.c
Tich
Great gesture
nice gesture Tich m8,what size did you end up ordering
kevG
Hi Kev
These as Suggested by our own Ca_Varminter from over the pond ...
BS017 Nitrile 90 O'Rings pack of 50
Are these correct?
Would you like some..lol
P.S I've not tried them yet..for about £5.50
Tich
Forget my pm
Tich, I've just ordered some too thanks for the info
Hi Dave
I've only just got your p.m!!
I've got loads I would have sent you some!
Tich
Quote from: maxtich on January 27, 2023, 02:12:08 AM
Hi Kev
These as Suggested by our own Ca_Varminter from over the pond ...
BS017 Nitrile 90 O'Rings pack of 50
Are these correct?
Would you like some..lol
P.S I've not tried them yet..for about £5.50
Tich
is that for the later RAW,I've always used 18 by 1.5 mm on the banjo on the RAWS that bso17 size is also used on the old theoben pressure gauge banjo
kevG
Ones I ordered are 17.7 x 1.78
These are what I've bought:
These O'Rings are made from Nitrile and have an ID of 17.16mm and a 1.78mm cross-section.
Tich
the banjo internal groove must be bigger than the standard normal ones then as 1.5 section is a very tight fit
kevG
I'm not going to tempt fate..by taking it to bits to find out if these fit..lol 8)
Kev do you thing these are the correct I rings!
I've never known for bso17 fit the banjo on either theoben/raw or impacts.its always been 18mm by 1.5mm.the bso17 was used on the theoben pressure gauge theoben adaptor .if you measure the reg diameter were the banjo fits its 18mm on all the rapids and raws/Impacts.
kevG
I've ordered by details given to me by our very own admin ..
To measure that I've got to strip it down..I'm Not going to tempt fate :-[
Tich :-\
I will measure them today from the service kits I bought, I've already used them and fixed a leak so the ones in the kit are good
Tempting fate..I'm sure I still had a tiny leak as the gage had dropped over a couple of weeks!
I changed all the o rings ..found a possible suspect o ring on the valve.
fitted all new o rings and then also the new Banjo o rings that I'd ordered and they fit perfectly!
Quote from: maxtich on January 26, 2023, 07:18:55 PMOk Members..I've had a delivery of a good few o rings for Raw quick fill kits.
If anyone needs any just let me have your address and I'll post them f.o.c
Tich
if you can give me the correct size for the banjo in a raw quick fill please
BS017 Nitrile 90 O'Rings These fit in my Raw Hm1000x V quick fill
But they Don't fit the 180 version to the Rapid and Impact air that I've got!
Hth
ahh that's what I'm after I have the vtype quick fill
No worries Mate..
Send me your address and I'll put a few in the post
Cheers
thanks.. I think dave74 just answered this post a bit earlier today ..im sure his said he'd post a few ..if however not.. ill send you a pm
thank you much appreciated
jack
Ok Mate
Let us know if u need any
Cheers