Welcome to Theoben Rapid Forum. Please login or sign up.

Members
Stats
  • Total Posts: 22,074
  • Total Topics: 3,204
  • Online today: 23
  • Online ever: 1,511 (July 25, 2026, 07:29:23 PM)
Users Online
  • Users: 0
  • Guests: 7
  • Total: 7
  • Baidu (2)

Twitter YouTube Facebook

Theoben Rapid Forum

Click above to make a donation. Thank you for supporting The Theoben Rapid Forum.

hanging by a thread

Started by Squinty, March 07, 2022, 11:26:56 AM

Previous topic - Next topic

Squinty

Sad Sad x 1 View List

Andycoup

 :oI?d say so!!!

What?s the thread in the reg like?

nevadacowboy

Think you need to visit Best Fittings. They have both standard and MFR bottle valves.
Bob
Once a Sapper always a Sapper

Squinty

the reg is fine.. it was a brass BSA superten valve that came with my mk1 20.


Squinty

Quote from: nevadacowboy on March 07, 2022, 11:40:08 AM
Think you need to visit Best Fittings. They have both standard and MFR bottle valves.

Bob's?  Job done
Like Like x 1 View List

KCE

What would cause that problem?

Regards Kev.
Regards KCE
Admin.

Squinty

to start with it's an old  valve, probably 20 years since BSA used those and I have no idea of its history.
Supetens were brass on brass not stainless like Rapids.

Could have been over tightened, I know that some Theoben bottle holders had a wider push pin that BSA bottles smaller outlet wouldn't go over.
Maybe spent some time on a tight/sharp bottle holder which has further stressed the thread.. it is brass.

I have new BSA brass valves on my FAC bottles and the the gun had BSA valves modified by AWT before that.
They lasted 12-13 years and only replaced those because I had to cut them off the bottles after they leaked.

Ca_Varminter

#7
Time for a Dr Bob bottle Valve!!
Brass is NOT my first choice for High Air Pressure fittings!!


Stuart

Squinty

#8
already done  ;)








Ca_Varminter

How about a Dr Bob Bottle Cap!!
It seal on the Bottle O-ring!!


Stuart

Squinty

how about 2.99 for 5 pipe caps?

angrybear

That's not a Helicoil is it  :o
You've got to go some to take a complete thread off like that  ??? that's a five white knuckles job  :-[

Squinty

Quote from: angrybear on March 07, 2022, 09:22:30 PM
That's not a Helicoil is it  :o
You've got to go some to take a complete thread off like that  ??? that's a five white knuckles job  :-[

Nope, it sure ain't a helicoil.

The bottle /valve came with my mk1 20, I'd hadn't used it and kept it as a spare.
As previously mentioned - no idea of the history.

Rather than take one of the c/f bottles of my other Rapids I used it to check the reg.
I unscrewed the bottle 1-1/8 turns before purging the tester and POP.
To start with I thought it was the o-ring going a bit early.

if it had gone 15 minutes earlier when I topped up to 200bar..that might have been a clean pants moment  :o

phil.m

From the thumbnail, I thought "why put a spring in there?"

Then I clicked on the picture.  :o

Glad you're fine & the bottle isn't in a neighbor's living room wall  ;)

This website is proudly hosted on Crocweb Cloud Website Hosting.

Crocweb Cloud Website Hosting

Welcome to the Theoben Rapid Forum

© 2026 Theoben Rapid Forum. All rights reserved.