Welcome to Theoben Rapid Forum. Please login or sign up.

Members
Stats
  • Total Posts: 22,074
  • Total Topics: 3,204
  • Online today: 63
  • Online ever: 1,511 (July 25, 2026, 07:29:23 PM)
Users Online
  • Users: 0
  • Guests: 70
  • Total: 70

Twitter YouTube Facebook

Theoben Rapid Forum

Click above to make a donation. Thank you for supporting The Theoben Rapid Forum.

Hammer springs - good source?

Started by Tim_B, August 22, 2021, 07:06:17 AM

Previous topic - Next topic

Tim_B

Hi all....I'm on the lookout for a good source of different hammer springs for my block buildout.  All the springs I have are too strong and makes the cocking a bit of an effort.

Ideally I'd like to try different lengths, weights etc so I can make the cocking like my other two rapids   :o

So, where do you source yours from? 

nevadacowboy

I got a set of springs from Bucketboy consisting of 5 hammer spring, 5 inertia weight springs and 5 exhaust valve springs.  The were made to the original Theoben specification. Also TR Robb used to do sets of assorted strength springs.
Like Like x 2 View List
Bob
Once a Sapper always a Sapper

Tim_B

Quote from: nevadacowboy on August 22, 2021, 02:33:30 PM
I got a set of springs from Bucketboy consisting of 5 hammer spring, 5 inertia weight springs and 5 exhaust valve springs.  The were made to the original Theoben specification. Also TR Robb used to do sets of assorted strength springs.
Thanks - yes I have those same sets, but looking for something a bit softer.

Tim B

KevG

Vincent springs did the original theoben springs.thats were I get mine from.i guess they could make you one offs.very good company
KevG
Like Like x 2 View List
Regards KevG.
Administrator

Squinty

#4
there's not really that much effort in cocking a sub-12?

I have tried a few different wire diameters and rates by ordering stock compression springs from various companies.
the lower diameter wires needed too much preload or rattled/ twanged/zinged in the hammer.

One other problem is getting the guides to fit as o/d and i/d aren't exactly the same.

My mk2 177 runs 11.6 using a 54-55mm spring and 95bar... the works being done up front by a bigger port valve 6x6mm and a 19" barrel.
But that's an air miser.. 500 shots from a 480cc bottle at 230bar  ;D

If you're having to use a stiffer / longer spring- maybe you need to up the reg pressure and settle on a shorter faster 'tap with better flow '?

essentially the spring travel only needs to be long enough to cock and have enough load to stop hammer bounce

Tim_B

Thanks All.

I have sent a mail to Vincent springs, so lets see what they come back with.

@squinty - I''ll try with some slightly short springs (I'll give them a measure)....however the softest spring I have in there is still a right pull to cock the hammer - significantly more than my other two rapids.

The reg pressure is set around 100 bar, which is about right for a .177 and is really consistent....so maybe it is about the length of spring.....thanks for the advice, I'll give it a whirl.

Daztilley

I have noticed on my rapids that the hammer cap spring seat can be shallower or deeper between different rapids - even with the hammer cap flush with the block. That might account for the difference in cocking effort with the same spring length ..... its always an idea to remove the cap and spring and check that the bolt body and cocking dog aren't rubbing or catching inside the block too , that can add to the felt cocking effort 👍
Like Like x 1 View List
Regards Daztilley
Moderator

KevG

also different trigger rapids can have the hammer at a different position when cocked.on my mk1 thats reged I've got an extra long pip(20mm).to shorten hammer stroke and speed things up.made for a much better and faster firing cycle.still very easy to cock.
KevG
Like Like x 1 View List
Regards KevG.
Administrator

angrybear

Quote from: Daztilley on August 23, 2021, 01:26:40 PM
I have noticed on my rapids that the hammer cap spring seat can be shallower or deeper between different rapids - even with the hammer cap flush with the block. That might account for the difference in cocking effort with the same spring length ..... its always an idea to remove the cap and spring and check that the bolt body and cocking dog aren't rubbing or catching inside the block too , that can add to the felt cocking effort 👍

And check the face plate, some of them need a quick dressing with an oil stone on the corners to make the throw smooth.

This website is proudly hosted on Crocweb Cloud Website Hosting.

Crocweb Cloud Website Hosting

Welcome to the Theoben Rapid Forum

© 2026 Theoben Rapid Forum. All rights reserved.