Theoben Rapid Forum

Theoben General Chat Area => Theoben Rapid Discussion => Topic started by: Topsparx1 on August 17, 2020, 09:15:30 AM

Title: Cocking Lever
Post by: Topsparx1 on August 17, 2020, 09:15:30 AM
Can anyone tell me if the original Rapid 7 cocking bolt lever is made of hardened steel the same as the bolt itself ? I want to modify it but if its hardened I'll have to replace it instead.
Title: Re: Cocking Lever
Post by: Topsparx1 on August 17, 2020, 08:14:49 PM
OK no takers on that one, how about this one, does anyone know the thread size of the cocking bolt handle where it screws into the cocking bolt ??
Title: Re: Cocking Lever
Post by: Kernal on August 17, 2020, 08:18:47 PM
Best wait for KevG m8, He`ll answer that for you or Stuart maybe,  They`ll be on later!

Title: Re: Cocking Lever
Post by: Ca_Varminter on August 17, 2020, 09:31:44 PM
Yes I do believe they were case harden after Machining.
Just looking at the ones I have..  they show very little wear....
You Might want to wait for KevG to chime in!!

Stuart
Title: Re: Cocking Lever
Post by: KevG on August 17, 2020, 10:04:20 PM
yes like bell metal.
KevG
Title: Re: Cocking Lever
Post by: Topsparx1 on August 18, 2020, 12:01:23 AM
Ok so it cant be modified 😏 any idea of the thread size into the cocking bolt ??
Title: Re: Cocking Lever
Post by: Ca_Varminter on August 18, 2020, 01:01:49 AM
1/4" x 28 threads per inch

Stuart
Title: Re: Cocking Lever
Post by: Topsparx1 on August 18, 2020, 08:25:27 AM
Thanks Stuart perfect 👍🏻
Title: Re: Cocking Lever
Post by: Topsparx1 on August 20, 2020, 11:18:29 AM
Me again, any of you lathe owning - engineering types able to make me something like the cocking lever in the pic. The guy made it from stainless steel and delrin but says he's too busy ATM to make one for me. Preferably the stainless steel could be replaced with normal steel so it can be blued as I don't want it shiny. Let me know guys this is the last piece of the jigsaw then the Mk1 R7 is complete.
Title: Re: Cocking Lever
Post by: Ca_Varminter on August 20, 2020, 03:36:50 PM
I am a bit far away.....across the pond..
But I have made these...
Using the tactical bolt handle made for bolt action center-fire rifles..
(https://photos.imageevent.com/scl_electronics/gun/ultimaterapid/websize/MyBoltjpg.jpg)
Thew stems are Stainless and Titanium...
The knobs at hard anodized aluminum.
Am sure you can find someone close by to turn a stem out for you!

Good Luck,
Stuart
Title: Re: Cocking Lever
Post by: KCE on August 20, 2020, 04:13:56 PM
im sure Dr Bob has some new ones he has had made.
Drop him a pm im sure he can help or kevG.
Regards kev.
Title: Re: Cocking Lever
Post by: Topsparx1 on August 20, 2020, 04:31:27 PM
Quote from: KCE on August 20, 2020, 04:13:56 PM
im sure Dr Bob has some new ones he has had made.
Drop him a pm im sure he can help or kevG.
Regards kev.
I spoke with Bob last week, his teardrops are silver stainless steel not really what I'm after, those ones that Stuart just put up are closer but again the shiny shaft is not right for me. I am trying to make my own with a bit of black acetal, the old Mk1 bolt, araldite, a drill press and a multitude of files and emery cloth !! God help me 🤣🤣

Something like this would work, its a standard teardrop that has been cerakote finished, nice tough Matt black finish. This was for sale a few years ago on eBay popped up in an image search.

Title: Re: Cocking Lever
Post by: Ca_Varminter on August 20, 2020, 07:05:19 PM
It is not the hard to get the stem blued..if made out of steel!!
Here is an offset bolt I made for the 10/22 rimmy I have been machining up..

(https://photos.imageevent.com/scl_electronics/cfguns/rimfire/websize/Bolt-handle.jpg)
(https://photos.imageevent.com/scl_electronics/cfguns/rimfire/websize/Bolt.jpg)

I use an excellent cold bluing solution called Oxypho-Blue.
Secret to get a dark blue... Heat the part up first with a heatgun or hair-drier first!!

So get them made out maybe 4140 steel...blue it you are on your way....

Good Luck
Stuart
Title: Re: Cocking Lever
Post by: Topsparx1 on August 21, 2020, 10:43:50 AM
Well I had a go and the final product in pics below, it's not the prettiest but it's comfortable and it works so as far as I'm concerned its a good result and only cost me a tenner for the plastic acetal 😃😃😃😃😃 👌🏻👌🏻👌🏻👌🏻


Title: Re: Cocking Lever
Post by: KCE on August 21, 2020, 10:49:45 AM
That is spot on and looks the part.
And you made it with basic tools good on you.
Regards kev.