Theoben Rapid Forum

Theoben General Chat Area => Theoben Rapid Discussion => Topic started by: Dr Fox on May 18, 2026, 02:48:40 PM

Title: MK2 Rapid barrel wedges set.
Post by: Dr Fox on May 18, 2026, 02:48:40 PM
Is anyone able to help? Have a need at his moment in time to renew the wedges in my FAC rifle. Dr Bob cant help until the end of the month. Has anyone got a set on sell, or lend to be replaced later.
Title: Re: MK2 Rapid barrel wedges set.
Post by: Ca_Varminter on May 18, 2026, 02:58:31 PM
I am sure you can find someone with a Lathe and Mill.
EZ to make, depending the Material used!
The Titanium ones I made was bit of challenge..
Tapping the threads for the bolt..
But it all ended well.

Stuart
Title: Re: MK2 Rapid barrel wedges set.
Post by: Dr Fox on May 18, 2026, 04:49:06 PM
Thank you Stuart
These I want to  replace
Title: Re: MK2 Rapid barrel wedges set.
Post by: Ca_Varminter on May 18, 2026, 05:25:29 PM
Yes...
The Barrel Pinch clamp...

Stuart
Title: Re: MK2 Rapid barrel wedges set.
Post by: anthony on May 19, 2026, 09:16:25 AM
Quote from: Dr Fox on May 18, 2026, 04:49:06 PMThank you Stuart
These I want to  replace

theres a set on the bay for £24
Title: Re: MK2 Rapid barrel wedges set.
Post by: anthony on May 19, 2026, 09:19:08 AM
just found another set on the bay for £16.99
Title: Re: MK2 Rapid barrel wedges set.
Post by: Dr Fox on May 19, 2026, 11:12:29 AM
Anthony
Thank you for your time, you are the man. I have the set at £16.99. Cheers Denis
Also every body else who advised on this.
Title: Re: MK2 Rapid barrel wedges set.
Post by: angrybear on May 19, 2026, 12:18:42 PM
Quote from: Dr Fox on May 19, 2026, 11:12:29 AMAnthony
Thank you for your time, you are the man. I have the set at £16.99. Cheers Denis
Also every body else who advised on this.

I wouldn't touch anything that seller makes with a barge pole  :o buy the originals for an extra £5  :-[
Title: Re: MK2 Rapid barrel wedges set.
Post by: Squinty on May 19, 2026, 12:29:28 PM
surprised that you need to replace the the clamps, are you sure that they haven't been over tightened and the block is now loose?

Title: Re: MK2 Rapid barrel wedges set.
Post by: angrybear on May 19, 2026, 12:34:57 PM
Quote from: Squinty on May 19, 2026, 12:29:28 PMsurprised that you need to replace the the clamps, are you sure that they haven't been over tightened and the block is now loose?

Hells teeth  :o never seen that before.
Title: Re: MK2 Rapid barrel wedges set.
Post by: Squinty on May 19, 2026, 12:43:18 PM
Quote from: angrybear on May 19, 2026, 12:34:57 PM
Quote from: Squinty on May 19, 2026, 12:29:28 PMsurprised that you need to replace the the clamps, are you sure that they haven't been over tightened and the block is now loose?

Hells teeth  :o never seen that before.

yeah  :(  I learnt a lot from that one
Title: Re: MK2 Rapid barrel wedges set.
Post by: KevG on May 24, 2026, 10:04:49 AM
barrel clamps should last forever.
kevG
Title: Re: MK2 Rapid barrel wedges set.
Post by: Bigal. on May 31, 2026, 10:43:34 AM
Last lever block here runs 3 grub screws to hold it down. 
Block a real fit on barrels going in.
So there not working to much. ;)
Title: Re: MK2 Rapid barrel wedges set.
Post by: Dr Fox on June 01, 2026, 09:59:46 AM
Let me give you the full picture. Life was sweet Full FAC performance, new life added with the Zulus V2 fitted until! My single shot loader refused to fit, it had always done before? A new multi shot aftermarket mag arrived, that would not fit either. Had the barrel moved?
In hindsight no cant happen! But at the time what's going on? So off barrel and it was noticed the locks had wear ridges, so replace. The refit advice was, Magazine piece of paper behind, slide barrel back to touch then lock up. Wrong!! Accuracy suffered extreme spread doubled. There is only one place this barrel can lock up, and thats after the locating grub screw is in its full position. any deviation from this causes the valve port and barrel port to misalign. After achieving this, Magazines from 3 different makers fit perfectly, and harmony is restored 32.4 ft lbs, extreme spread 8 fps. If the mag is too tight to enter loading port, then its odds on its not the rifle at fault.