For the longer blocks
KevG
Those look amazing...Great Finish..Stainless?
Stuart
Cheers stuart m8.yes I like doing things in stainless.
KevG
Are those what I saw today kevG.
The same as you fitted on mine which I have noticed a vast improvement in the past few weeks.
When I look at it on the rapid it is as though it was part of the gun when it came from the factory it really does blend in with the action.
Regards Kev.
Looks great Kev, I bet the customer will be pleased with that ;)
hope so m8.could not leave it while tomorrow.so finished it tonight,just the carbon tube to fit now.
KevG
Quote from: KCE on June 05, 2020, 10:35:26 PM
Are those what I saw today kevG.
The same as you fitted on mine which I have noticed a vast improvement in the past few weeks.
When I look at it on the rapid it is as though it was part of the gun when it came from the factory it really does blend in with the action.
Regards Kev.
yes kev m8,but made the stand of after you went,was going to do it tomorrow but once i get started i carnt stop.
KevG
Looks great kev 👍
That will add loads of air capacity to the valve chamber 👍👍👍
got something similar in my little .20 cal daz and its realy upt the shot count.
KevG
I remember seeing a pre chamber fitted to the bottom of the block too - have put pics below.....
With MFR s being fitted with a shrouded barrel there isnt space to fit a chamber below the barrel - looks a tidy piece of work too 👍
OMG...
That just reminded me another pre-chamber connected through the bottom of the receiver.
Swift on AirguAdvice...His .50 cal Big bore Rapid project....
I don't have any photos
Stuart
That sounds interesting Stuart! Never seen a 50 cal rapid either 😲
Quote from: KevG on June 05, 2020, 09:55:04 PM
For the longer blocks
KevG
Hi Kev, whats a HEIC file and what will it open with
G
apple device
Hey KevG...
Do You Send to the States???
:o :o :o :o :o :o :o :o :o ::) ::) ::) ::) ::) ::) ::)
Stuart
Depends if your m8 Donald Trump says it's ok.😁
Yes I have done in the past stuart m8
KevG
Quote from: KevG on June 07, 2020, 08:39:07 PM
Depends if your m8 Donald Trump says it's ok.😁
Yes I have done in the past stuart m8
KevG
He Is No M*8 of mine...
I was hoping he would stay on your side of the Pond With Boris!!!
:P :P :P :P :P :P :P
Thanks,
Stuart
Quote from: KevG on June 06, 2020, 12:19:56 AM
got something similar in my little .20 cal daz and its realy upt the shot count.
KevG
What spec stainless did you use Kev? What wall thickness if it also please?
316 stainless 2.9mm wall on main chamber and 2.3mm wall were thread relief is.
kevG
Thanks Kev. Have you made any from titanium? I would imagine weight penalty for stainless compared to titanium is negligible for such a small amount of material used?
Do you cut the thread using lathe, or use a die?
do it on lathe.stainless would be tough to do with die..sooner do them out of stainless.i guess they could be done in brass but always think it looks a bit naff and cheap.
KevG
I thought you Yorkshire men loved brass! But only if it stays in your pocket I suppose! ;)
Quote from: Brooksy on July 14, 2020, 07:26:51 AM
I thought you Yorkshire men loved brass! But only if it stays in your pocket I suppose! ;)
;D ;D ;D ;D ;D ;D nice,
(https://media.giphy.com/media/l3HBbltOYjoNq/giphy.gif)
I wonder if you could make up something like this for me ..
would need to go between the regged raw quick fill as in the picture..
have no idea on cc capacity I'd imagine 2cc