Hi all,
MY reg finally started leaking,and after fitting new seals it is giving me nothing but trouble.
If I screw the valve core in all the way, it seems to block the reg and no air gets through from the bottle. If I back off the reg core from the Outer Body, I get leaking from the bottle to reg interface.
Should the reg core be screwed fully tight to the reg body? The end of the reg core is sealed off with a small bit of nylon? it seems like this is bottoming out on the back of the push pin stopping air getting in if the core is screwed up tight. Should this piece of nylon/Delrin be there?
Cheers
Well it looks like you have Multiple problems.....
The Nose seal in your photo needs to be replaced!
It could have been damaged if you turn the reg core
to forcefully....
As to the air leak...
This due to one of many O-rings the could be involved...
Depending where is the air leaking From!
KevG is you man to fixed it up!!
Good Luck,
Stuart
thanks Stuart.
Quote from: Ca_Varminter on June 05, 2020, 05:11:51 PM
Well it looks like you have Multiple problems.....
The Nose seal in your photo needs to be replaced!
It could have been damaged if you turn the reg core
to forcefully....
As to the air leak...
This due to one of many O-rings the could be involved...
Depending where is the air leaking From!
KevG is you man to fixed it up!!
Good Luck,
Stuart
Thanks Stuart,
in normal use I assume the valve core should be finger tight to the body? Am I right in saying I have a micro reg core? Kev did service the reg years ago but I cant remember if he fitted one of his cores or not!
Quote from: JoeB on June 05, 2020, 04:35:58 PM
If I screw the valve core in all the way, it seems to block the reg and no air gets through from the bottle. If I back off the reg core from the Outer Body, I get leaking from the bottle to reg interface.
If it is leaking where the bottle meets the Reg.
Then it is the small O-ring on the depressing pin...
(https://photos.imageevent.com/scl_electronics/gun/air/MFR%20Oring.jpg)
hth,
Stuart
thanks Stuart, yes I have changed that too.
its really odd, in that if the reg core is screwed down hand tight, no pressure gets through the reg at all, but also the bottle doesn't leak at the interface.
However, if I unscrew the reg core by approx. 1/2 turn, I get pressure behind the reg but then the bottle interface also leaks! I just don't understand it at all. Is it possible the valve pin in the reg has moved/turned within the reg body somehow? I don't have the tool to remove it, but it seemed tight when I tried to rotate it with a couple of drill blanks but its all I can think of as it was ok before I touched anything other than a small leak from the reg breather hole.
Quote from: JoeB on June 05, 2020, 06:00:07 PM
thanks Stuart, yes I have changed that too.
its really odd, in that if the reg core is screwed down hand tight, no pressure gets through the reg at all, but also the bottle doesn't leak at the interface.
However, if I unscrew the reg core by approx. 1/2 turn, I get pressure behind the reg but then the bottle interface also leaks! I just don't understand it at all. Is it possible the valve pin in the reg has moved/turned within the reg body somehow? I don't have the tool to remove it, but it seemed tight when I tried to rotate it with a couple of drill blanks but its all I can think of as it was ok before I touched anything other than a small leak from the reg breather hole.
Well now we are back to a multiple problems..
First, when you screwing down the reg core..Tight.
You have just smashed the nose seal against the air inlet nozzle.
So No air coming in..no air to leak....
So when you hear air leaking at the bottle junction when you loosen the core
This slounds like the seal behind the push-pin/inlet disk needs replacing...
(https://photos.imageevent.com/scl_electronics/gun/air/websize/reg-front-strip1.jpg)
(https://photos.imageevent.com/scl_electronics/gun/air/websize/reg-front-strip2.jpg)
Your Reg should have two holes.. Like the one in my photo..
The larger threaded hole is for the grub screw that Locks the inlet/depressing disk in place!
If you hear air coming from the bleed/equalization hole.. this is a O-ring sealing problem with the core..
KevG is the person to talk to over there..
He can fix the leaks a set it for you
Good Luck,
Stuart
Thanks Stuart, that makes sense now.
A man with a little knowledge (me) is a dangerous thing!
I had assumed the push pin/inlet disc was screwed in. I didn't realise it had a seal behind it. I will try to get hold of Kev.
I'm finding this a fascinating read.
Some very good info and advice and quality photos to help learn along the way.
Thank you Stuart.
Quote from: KCE on June 05, 2020, 07:29:13 PM
I'm finding this a fascinating read.
Some very good info and advice and quality photos to help learn along the way.
Thank you Stuart.
Thanks...
Well before YouTube...Photo were worth a Thousand Words!
So with My Nikon D3x, I like Quality photos to help people Visualize
What is going On!!
Stuart
The oring on the locking collar may be tired.alowing you to screw the collar in to far.you should have travel on the core.if you remove nylon nut and belleville washers you can then check travel.you may have none and have reg lock.thing is the collar needs to be finger tight.so you may need a new oring.the purpose of the oring is to give you some adjustment as there are 4 parts to the reg that dictates this.with things being mass produced you get tolerance differences.the oring is not a very good idea as they age and can go hard or perish a d can upset the reg settings.
KevG
Cheers Kev/Stuart,
After Stuart showed me the O ring behind the push pin which I never knew existed I had another go. I changed that one, and tried again. I have managed to get it working with no discernible leak, shooting very consistently. However this still required me backing off the reg core collar. I suspect maybe I used the wrong O ring on the core and needed a bigger cross section than I used. This would hold the core back as Kev says and allow it to be done up finger tight. I ordered a new seal kit earlier so when that arrives I will also check what seals it has and compare. I used seals I have previously bought many years ago but maybe the one I needed was previously used up and I therefore used the wrong one. The one I took off was knackered so difficult to determine what size it should have been!
When you can fit me in Kev, can I send the reg to you for a proper once over and potentially upgrade? -you last serviced the reg about 8years ago but I know how busy you are!
Thanks again everyone. Great to have a proper forum again. Between Stuart and Kev, you both first gave me advice when I bought my first rapid 11years ago, and its great to see you still here passing on your knowledge.
Thank you JoeB for your kind words.
This is why we set up this forum and it is still in development to make it a very friendly place to be and help give advice and info to members in there hour of need.
I'm glad you have sorted out your problem with the help of the forum members it shows we are on the right track with what we are doing.
Regards Kev.
This is why this Forum exists..
Anyone can get help with their Rapid....
And the help can come from Everyone Here!!
KevG, the True Professional Airgunsmith here.
Me, I 'm the engineer that does gunsmithing as a hobby..
But Rapids are a Passion for me!!
Cheers,
Stuart
Just noticed on the picture the core sealing face is trashed.this can cause a lazy reg and creep.
KevG
I noticed that kev looks black usually derlin clear it needs redoing or refacing
Some were black daz..looks like an old one of mine as I've not done then like that for around 10 years.
KevG
Quote from: KevG on June 05, 2020, 10:27:13 PM
Some were black daz..looks like an old one of mine as I've not done then like that for around 10 years.
KevG
You're right Kev. It lasted a while. :-) however over the years I have slowly knackered it with the odd seal change etc. Can I send my reg up to you for a 1decade service? ! -i think it probably was 2010 when you did the reg for me last time.
That's lasted well then joe m8.use a better sealing face material now.
KevG
Cant argue with 10 years of use 👍👍👍
Excellent thread this ,and with great pictures and explanations 8)
atvb' Mick
As my reg was creeping I sent it off to kevg for a new updated core, and whilst I was at it also went for one of kevs double tap inertia weights. Kev turned it round in double quick time and I fitted them today. Straight off the bat with no fettling it was running a sweet 785fps with 8.4gn AA field. The double tap inertia weights made a definite decrease in noise too so double impressed. Cheers Kev. Excellent as always. :-)
Glad it's running ok joe m8
KevG