Theoben Rapid Forum

Theoben General Chat Area => Theoben Rapid Discussion => Topic started by: angrybear on April 19, 2025, 08:43:43 PM

Title: STX Smooth twist liner
Post by: angrybear on April 19, 2025, 08:43:43 PM
Just got hold of one cheap, with the intention of adapting it to an MFR to try/use slugs.
Someone must have had a go already any hint's tip's welcome.

The current plan is a brass "breech" end & inset the liner just shy of the port, sleeve with carbon for support & then shroud the lot  ???
Title: Re: STX Smooth twist liner
Post by: Ca_Varminter on April 19, 2025, 10:02:22 PM
Yes...
I know few that have made Breech extension the screws into the steel barrel outer sleeve.
It also has the internal O-ring to seal the smooth-twist barrel liner.

Stuart
Title: Re: STX Smooth twist liner
Post by: Dave74 on April 20, 2025, 03:02:43 PM
Yes running a few superior liners got it made so the liners can be changed over, liking the 600mm heavy slug version.
Title: Re: STX Smooth twist liner
Post by: Therapidman on April 20, 2025, 07:17:27 PM
Been there and spent a load of money on them liner making them fit. 500mm might be OK but the 600mm and 700mm are just to bendy even with carbon stiffer... if you want a slug barrel buy a alfa barrel
Title: Re: STX Smooth twist liner
Post by: Therapidman on April 20, 2025, 07:19:56 PM
I have 3 made you could set the gun up shooting perfect put it away getbit out day after and would have changed zero .. there is to much flex in them .. I think that's why the fx have a bad name for them not holding zero
Title: Re: STX Smooth twist liner
Post by: Dave74 on April 20, 2025, 07:54:29 PM
Mine holds zero fine  so much different ways to set liners up, been through all that and got there in the end.
Title: Re: STX Smooth twist liner
Post by: DAVYW1 on April 20, 2025, 08:28:58 PM
My tensioned liner setup holds zero fine. The liner is permanently attached to a steel breech end, a carbon tube covers the liner and slots into the breech end and then a tensioned metal end with a threaded end is attached to the muzzle end of the liner. When you tension the muzzle nut the liner is tensioned between the two ends and supported by the carbon tube. If i could figure out how to put up pics i'd show you what i mean?!
Title: Re: STX Smooth twist liner
Post by: Squinty on April 20, 2025, 08:39:14 PM
Been messing about/ mulling over a 500mm/19" .177 Superior liner for quite a while now, my pillar drill went bzzzz-pop last week so haven't got any closer to finishing.
Porting, shroud fixings and splitter to finish still ::)

Was going to make a collet holder affair which didn't turn out as expected... down to 16" now.

Not the ideal route perhaps but I threaded the liner, stainless breech block and alloy splitter  M-7x0.75 and will bond the liner into the breech.
The Cf stiffener is recessed 15mm into the breech block and 10mm into the splitter and even with light tension it still seems that there is some flex although the shroud should hold tight.
Title: Re: STX Smooth twist liner
Post by: KevG on April 22, 2025, 08:59:08 PM
made a couple with great success.they sit in 14mm shower pipe.sturdy as you like with no zero shift problems.
kevG
Title: Re: STX Smooth twist liner
Post by: Brooksy on April 22, 2025, 09:03:27 PM
Quote from: KevG on April 22, 2025, 08:59:08 PMmade a couple with great success.they sit in 14mm shower pipe.sturdy as you like with no zero shift problems.
kevG
14mm shower pipe? What's that Kev, the chrome pipe or copper?
Title: Re: STX Smooth twist liner
Post by: KevG on April 22, 2025, 09:17:34 PM
chrome paul m8
kevG
Title: Re: STX Smooth twist liner
Post by: Brooksy on April 23, 2025, 06:44:13 AM
I see what you mean Kev. 14mm internal diameter, 15 mm outer.
Title: Re: STX Smooth twist liner
Post by: Dave74 on April 23, 2025, 07:15:01 AM
The liners are roughly 8.3mm diameter iirc.
Title: Re: STX Smooth twist liner
Post by: Ca_Varminter on April 23, 2025, 02:11:08 PM
Quote from: Dave74 on April 23, 2025, 07:15:01 AMThe liners are roughly 8.3mm diameter iirc.
Depends on Caliber.......

Stuart
Title: Re: STX Smooth twist liner
Post by: Dave74 on April 23, 2025, 04:56:50 PM
O ye never thought of that I only been using .22, guess that's why the stiffner tubes are calibre specific
Title: Re: STX Smooth twist liner
Post by: angrybear on April 27, 2025, 11:42:46 PM
Well the first part went well enough, just waiting for the 12 x 8mm tube to arrive.
Title: Re: STX Smooth twist liner
Post by: Tim_B on April 28, 2025, 05:40:52 AM
Looking good - will be interesting to see the results as if its a good liner then no reason why it won't be accurate.

I actually have a short .22 liner and shroud in the shed awaiting testing....just never got round to it.  The thinking was it would make a great ratter :-)

Looking forward to the next stage.
Title: Re: STX Smooth twist liner
Post by: angrybear on May 06, 2025, 04:58:19 PM
Well I got the carbon stiffener tube, put it all in a shroud & decided to test it before making any baffles,
Glad I did because I'm thoroughly underwhelmed with the performance  ???
Rubbish with JSB pellets, pretty accurate with ZAN 15gn lead free slugs, but not overly accurate with FX hybrid slugs,
which are far too heavy for sub 12 anyway.

Interesting build but less than successful.

Title: Re: STX Smooth twist liner
Post by: Therapidman on May 06, 2025, 06:42:31 PM
I did try and warn you ... there not worth messing around with.... and to be honest you need at least 900fps for slugs