Theoben Rapid Forum

Theoben General Chat Area => Theoben Rapid Discussion => Topic started by: Hobbyman2007 on February 14, 2025, 02:11:53 PM

Title: New to me MK2 .25
Post by: Hobbyman2007 on February 14, 2025, 02:11:53 PM
New member here with a few pics of a recent acquisition. I don't have much info on this particular rifle other that what was advertised. If anyone recognizes this rifle or knows about it . Let me know.  The pics are from the add. It was posted on airgun nation and a Canadian used gun site.
Title: Re: New to me MK2 .25
Post by: Ca_Varminter on February 14, 2025, 06:20:57 PM
Well by the looks of it, your Rapid is one of the last to be made in the UK..
The last Version were stamped TheobenUSA, when they being produced by David Slade!
You should be able to look up the production date by Serial#
(https://photos.imageevent.com/scl_electronics/gun/misc/large/Rapud%20Dates.JPG)

Nice looking Rapid!!
Stuart
Title: Re: New to me MK2 .25
Post by: Hobbyman2007 on February 14, 2025, 08:10:45 PM
Thanks for sharing that sheet Stuart. From the pics the serial number is 025715. That would put it as a June 2011. I should mention is was imported to Canada in or around 2017 from Texas from what the previous owner told me.
Title: Re: New to me MK2 .25
Post by: Hobbyman2007 on February 17, 2025, 11:21:36 PM
Received the rifle today and can say that I'm quite pleased with how it looks initially. But because I'm a tinkerholic , immediately disassembled and had a good once over. The block has the fill port in the bottom plug location which I've not seen before in any pics , has the fast flow which I was expecting. The hammer and inertia assembly in great condition with zero signs of wear, however after measuring the pip length of 12mm I'm left wondering if I should do the silent pip mod now or later and maybe shorten it up to the 6 mm I've seen recommended for FAC rifles. The hammer spring setup is a twin spring affair and has about an inch of preload. This is going to get changed ASAP. After looking the innards over , I cleaned up the stock with denatured alcohol to get it ready for a few coats of true oil. I did notice the stock screw hole was a bit buggered up so I made up a quick threaded brass insert to fix it up and glued it in place. I'm its current state of tune it's shooting at about 40 fpe. Just about perfect speed for the JSB kings I have an abundance of.i don't have a trigger scale but I'm sure it's breaking at 8oz or less, no creep , short first stage and very little overtravel.

Should have acquired one of these beauties long ago, I'm really enjoying it so far.
Title: Re: New to me MK2 .25
Post by: Daztilley on February 18, 2025, 01:14:48 PM
Sounds great 👍
Title: Re: New to me MK2 .25
Post by: Kernal on February 18, 2025, 04:40:27 PM
Fantastic get modding it best thing i ever did to my Mrk 1   ;)
Title: Re: New to me MK2 .25
Post by: Hobbyman2007 on February 19, 2025, 01:25:12 AM
Got my hammer spring affair set correctly, went with two short stiff springs and am running them with no preload on the hammer, just to say they are making contact. Put a second coat of oil on the stock then moved on to tuning. For the initial fill I started at 220 bar. This started the string at 810FPS. And ended at a peak velocity of 890FPS which was between 145 and 150 bar. Hard to say as there's no gauge and was relying on what the gauge on the tank read when the check valve opened on the next fill. Next I filled to 180 bar which started at 865FPS. Just about perfect. I can't believe how easy it is to work on this rifle.

What is everyone else using to lock the hammer spring adjuster in place?
Title: Re: New to me MK2 .25
Post by: Ca_Varminter on February 19, 2025, 01:50:14 AM
Quote from: Hobbyman2007 on February 19, 2025, 01:25:12 AMquote author=Hobbyman2007 link=msg=22728 date=1739928312]
What is everyone else using to lock the hammer spring adjuster in place?

If you have a problem with the hammer backing out...
A Drop of Blue Loctite should do it!
Stuart
Title: Re: New to me MK2 .25
Post by: Hobbyman2007 on February 20, 2025, 02:47:16 PM
Well as I mentioned before I'm a tinkerholic and can't leave well enough alone. Placed an order for a 580cc carbon bottle and bottle valve. And now I'm searching for a Rapid air works V block so that I can monitor fill pressure but they are sold out. Once I find it I'm going to remove the existing bottom fill port and add a pre chamber extension I've got enough material on hand to take care of that. Anyone else make V block /gauge fill ports that don't move the bottle forward it n the stock? Dr.bobs design is good but I'm not sold on the extra room it takes.
Who knows , I may end up regulating the rifle if I can find the right bits. Rapidairwerks seems like the only viable option for these parts.
Title: Re: New to me MK2 .25
Post by: Ca_Varminter on February 20, 2025, 03:58:57 PM
Well I had to make own QF banjo and FF adapter for my Rapid..
So if you have the tools and material.. it is not that hard....

original RAW QF with Reg and Gauge....
(https://photos.imageevent.com/scl_electronics/gun/qf/websize/9image_1.jpg)

My custom banjo made from 7075 aluminum, and turned down FF adaptor.
(https://photos.imageevent.com/scl_electronics/gun/qf/websize/image_1.jpg)
(https://photos.imageevent.com/scl_electronics/gun/qf/websize/image_5.jpg)

Stuart
Title: Re: New to me MK2 .25
Post by: Hobbyman2007 on February 20, 2025, 04:26:01 PM
That's some nice craftsmanship. I am using a 9 x 20 chinesium lathe that gets me by but myself or my machine are not quite capable of making what I'm looking for.
Title: Re: New to me MK2 .25
Post by: Ca_Varminter on February 20, 2025, 06:14:52 PM
Well I can't say I have a Ultra-Precision Lathe....
It is just a Emco Compact 5!!!!
Benchtop...I wish I have the room in my little Man Cave
But my CNC Mill take up some Room too!!
(https://photos.imageevent.com/scl_electronics/misc/taigstuff/websize/enclosure5.jpg)

(https://photos.imageevent.com/scl_electronics/gun/ultimaterapid/websize/thin%20cut.jpg)
Making a Titanium Valve for one of my Rapids......

Stuart
Title: Re: New to me MK2 .25
Post by: Hobbyman2007 on February 21, 2025, 09:50:43 PM
Anyone ever add a chamber extension where the bottom plug is usually located. As you can see this rifle has a foster fill fitting but it'll be adding a RAW V block. It was my thought that the extra on hand air would help with consistency and if nothing else give me something to fill the hole with.
Title: Re: New to me MK2 .25
Post by: Squinty on February 25, 2025, 07:50:16 AM
Excuse my ramblings..

You haven't quite got it set up right if the power curve is a constant rise peaking at 150-155bar, either valve/ valve stem spring issues or too much preload.
Get the airflow right and you can use a single OE spring ;)

60fps extreme spread? should be able to get it down to 10-15fps (and better shot to shot).

I'm guessing the shot count is poor?
Probably getting some hammer bouce if there isn't any preload which won't help air use.

Does the buddy bottle have a valve pip or is it set up for unrestricted flow?
Such thing as too much airflow can mess with the power curve,
Sure more peak ME but can also lower optimal fill pressure perhaps 10 bar.

A 580 cc bottle will give more shots but fill pressure will be critica, overfill just gives a longer rise to the plateau. Power curve will need sorting out first.


Could probably fit a 1/4BSP digital mini guage in that hole if you need more accuracy for setting up,
I'd forgo the V-block for the sake of QF and a so-so guage and get a pre-chamber extension for a few CCs more volume.

Keep the bottom fill and make a new cover plate?

Outright volume is only really necessary for a reg, even the HMXs have limits.
Mick (Aggy) spent two years trying to screw FX slug power levels out of a .22 1000X and went back to a more reasonable 40fpe.

etiam viviens has also chases ME with his..shoots it on a tethered bottle with a reg extension?

Another option is a Huma HM1000 reg.givemore volume but needs either a blank collar or v-block.


Title: Re: New to me MK2 .25
Post by: Hobbyman2007 on February 27, 2025, 09:20:13 PM
I appreciate the reply squinty. To get rid of my ES being at 60plus fps. I've started filling to 180 bar and ending at 120 bar. This brought it down to 22 or so with a better spring set up. I'm currently shooting to keep the rifle in or around the 40 FPE mark with 25.4 gr. JSB kings. The rifle does have a factory fast flow  valve. I did notice the exhaust valve had been replaced with a single oring stem that was partially blocking off the transfer port when the valve was opening. I fixed that on the lathe by removing 2mm of material and blending it with the thin portion of the stem.
Now just because I like to complicate things, I've made a balanced valve by entending the existing valve through the rear cap using a top hat and I'm now making a lightweight hammer to match with the easy to open valve. I'll post pics of the new parts once I get everything dialled in.
Title: Re: New to me MK2 .25
Post by: KevG on February 28, 2025, 12:02:57 AM
could be well worth fitting a valve chamber extension (replaces valve end cap) and a shorter valve body and stem.
kevG
Title: Re: New to me MK2 .25
Post by: Hobbyman2007 on February 28, 2025, 01:20:47 AM
That's the plan now Kev. I was using a top hat over the existing valve to act as an extension. What I didn't take into consideration was that the top hat would be forced in the opposite direction by the pressurized air. Completely negating the whole point of a balanced valve. I've got some 304 stainless on the way to make a new stem that will go straight through the end cap that I made from a 1/4" BSPP to #4 JIC fitting I got from the local hydraulic shop, sealed with an oring in the extended rear cap. In the first pic there's my new light weight hammer made from 7075 aluminum bar stock with an adjustable silent PIP and the short stiff spring.The second pic is the modified rear cap installed for testing. It's a work in progress and I'm getting there slowly but surely.

Ultimately, I'm after a quick lock time with easy cocking and able to reach the 40fpe.
Title: Re: New to me MK2 .25
Post by: skagitmonster on February 28, 2025, 04:08:04 PM
Have you not thought about a reverse valve and plenum ( valve chamber extension ) does away with a lot of faff , a slightly heavier hammer maybe but stock hammer can be used
Title: Re: New to me MK2 .25
Post by: skagitmonster on February 28, 2025, 05:02:47 PM
Adjust pip size to suit...8mm 8.5mm etc
Title: Re: New to me MK2 .25
Post by: Hobbyman2007 on February 28, 2025, 08:47:04 PM
I'm not following the reverse valve idea. Do you happen to have a drawing or link?
Title: Re: New to me MK2 .25
Post by: KevG on February 28, 2025, 09:38:28 PM
think you will find aluminium far to soft a material for hammer.hammers need to be case harden.the sear contact on the hammer will soon chew up plus scratch were it runs along the trigger sear.
kevG
Title: Re: New to me MK2 .25
Post by: KevG on March 01, 2025, 12:58:54 AM
20250301_004738.jpg
I got great gains with this set
kevG
Title: Re: New to me MK2 .25
Post by: Hobbyman2007 on March 01, 2025, 02:47:43 AM
I've been looking at a sleeve to press over the hammer for the sear wear. Option 2 would be to have it anodized. Jury is still out on that one. Didn't get much time to work on it today but I should have a couple of hours tomorrow after this evenings snow storm gets cleaned up. Late February and we've just got another foot of snow. That's life in northern Ontario , Canada.
Title: Re: New to me MK2 .25
Post by: skagitmonster on March 01, 2025, 05:30:36 PM
It's just a reverse sprung valve , does away with anything in the valve chamber extension, kev g s has a similar principal ,both work
Title: Re: New to me MK2 .25
Post by: skagitmonster on March 01, 2025, 05:31:46 PM
I did post a pick but where it's gone I have no idea .....I'm not used to this forum yet
Title: Re: New to me MK2 .25
Post by: KevG on March 01, 2025, 06:04:55 PM
Quote from: skagitmonster on March 01, 2025, 05:31:46 PMI did post a pick but where it's gone I have no idea .....I'm not used to this forum yet
it's there now I have problems posting pics and ime admin😀
kevG
Title: Re: New to me MK2 .25
Post by: Hobbyman2007 on March 01, 2025, 09:55:30 PM
I don't know if you guys have been told yet, what a bunch of enablers. Hahahaha. I really like that reverse spring set up. That would give me the max onboard air and give me the ability to adjust the preload on the spring.

I'm running some tests now and let me just say, this valve is EASY to open. I need to dial it back some. Getting over 1000fps from a 17" barrel at 200 bar. Looking at a solution to get the valve to close sooner. I'll post pics with dimensions of the valve stem later on when I get it sorted out.
Title: Re: New to me MK2 .25
Post by: Hobbyman2007 on March 02, 2025, 03:40:33 PM
Here's a pic of the new valve stem with a sketch I used . I give up on the lightweight hammer. I just don't have the right springs here to make it work. I went back to the original hammer and inertia weight and a single spring with no preload , free flight/ slingshot hammer. Right back to 40 FPE with the JSB's even with the new shorter 17" barrel but much easier to cock. The valve stem is extending 8mm longer than the original shortening the stroke. Very fast lock time and the air release is a quick snap. Still waiting for a few parts but I'm real close to being  done with this one.
Title: Re: New to me MK2 .25
Post by: Hobbyman2007 on March 04, 2025, 11:28:24 PM
While I'm waiting for the V block from RAW I figured I'd get a jump on a hole plug for the stock. I saw a few pics from what Stuart had done with a couple of his. Here's what I came up with. A short 24mm OD 7075 aluminum sleeve for the hole. Then a delrin cover that gets held in place by a 1.5mm x 15mm ID oring. I had a stainless screw with a swivel from some camera gear I had laying around that got screwed into the cap. Not the most elegant fix but functional. I wanted it to be counter sunk a little further in the stock but as you guessed it my glue set too quickly and that's where it ended up.