Theoben Rapid Forum

Theoben General Chat Area => Theoben Rapid Discussion => Topic started by: GlynB on October 18, 2023, 09:36:30 AM

Title: Rowan trigger
Post by: GlynB on October 18, 2023, 09:36:30 AM
I have been looking at the above, has anyone had anything to do with the rowan trigger. Do they fit straight into the rapid and also will it work with a trigger guard fitted
Cheers
Title: Re: Rowan trigger
Post by: Ca_Varminter on October 18, 2023, 03:07:40 PM
Well before Rowan got involved with triggers for the Mark 4... I did my own...
Here is the first iteration.......
(https://photos.imageevent.com/scl_electronics/gun/ultimaterapid/websize/new-trigger2.jpg)
I chopped one of the Early "Stick" trigger arm and threaded a 1/8" rod into it.
Then I used an Anschutz adjustable Trigger blade!
Here is a photo of the early Stick and later Setback Triggers by Theoben...
(https://photos.imageevent.com/scl_electronics/gun/air/small/setback2_1_.jpg)(https://photos.imageevent.com/scl_electronics/gun/air/small/setback3_1_.jpg)
Then I got my CNC Mill and decided to redesign and Make it more Clean looking....
(https://photos.imageevent.com/scl_electronics/gun/air/websize/2012-02-14_14-59-45_679.jpg)
(https://photos.imageevent.com/scl_electronics/gun/air/websize/2012-02-15_13-31-45_250.jpg)
(https://photos.imageevent.com/scl_electronics/gun/air/websize/Mark4-tirg1.jpg)

Good Luck,
Stuart
Title: Re: Rowan trigger
Post by: Squinty on October 18, 2023, 05:56:10 PM
Yes they fit straight in, obviously they do need adjusting.
If you're putting it into a late mk1 ambi there isn't much room for travel

(https://i.imgur.com/wsex3Zz.jpg)
Title: Re: Rowan trigger
Post by: GlynB on October 18, 2023, 09:40:44 PM
Wow that's amazing work, but well, well beyond me
Thank you for the reply
Title: Re: Rowan trigger
Post by: GlynB on October 18, 2023, 09:42:19 PM
Quote from: Squinty on October 18, 2023, 05:56:10 PMYes they fit straight in, obviously they do need adjusting.
If you're putting it into a late mk1 ambi there isn't much room for travel

(https://i.imgur.com/wsex3Zz.jpg)

Yes thats exactly what I'm wanting to fit it to, thank you for the photo's, exactly what I was looking for
Thank you
Title: Re: Rowan trigger
Post by: KevG on October 19, 2023, 07:38:48 AM
real nice work that Stuart.
kevG
Title: Re: Rowan trigger
Post by: Ca_Varminter on October 19, 2023, 03:10:20 PM
Well if you want to get the most out your Mark 4 Trigger...
First make a set of Brass spacer/shims and hand fit them!
(https://photos.imageevent.com/scl_electronics/gun/ultimaterapid/websize/trig-bush.jpg)
(https://photos.imageevent.com/scl_electronics/gun/ultimaterapid/websize/trig-bush4.jpg)
This will eliminate any sideways wobble!!
Gives you a more Precise Feel!!
Also you can use Ball-Bearing tip screws on the trigger arm....if you can find them..
(https://photos.imageevent.com/scl_electronics/gun/ultimaterapid/websize/trig-polish.jpg)
Or just file to round off the cup on the tip of the standard grub screw, and polish them!!!

Have Fun!!
Stuart
Title: Re: Rowan trigger
Post by: Squinty on October 19, 2023, 05:18:43 PM
Quote from: GlynB on October 18, 2023, 09:42:19 PM
Quote from: Squinty on October 18, 2023, 05:56:10 PMYes they fit straight in, obviously they do need adjusting.
If you're putting it into a late mk1 ambi there isn't much room for travel

(https://i.imgur.com/wsex3Zz.jpg)

Yes thats exactly what I'm wanting to fit it to, thank you for the photo's, exactly what I was looking for
Thank you

you're welcome.

A quick correction- if you're looking to bring the blade backwards to reduce pull length with the sporter stock .....then there isn't much room for for a long trigger pull.
Does adjust down to a nice short squeeze tho.

Even though I have fairly large hands the straight mk4 blade felt a little too far forward in that stock and the mk4  set-back felt too wide as if my finger was on the edge rather than in the centre.

Was a little too far back when  in my S-type stock so moved it forward ...I almost wish I'd gone for the anodised button ;D

(https://i.imgur.com/ou9uail.jpg)
Title: Re: Rowan trigger
Post by: GlynB on October 19, 2023, 05:49:45 PM
Quote from: Ca_Varminter on October 19, 2023, 03:10:20 PMWell if you want to get the most out your Mark 4 Trigger...
First make a set of Brass spacer/shims and hand fit them!
(https://photos.imageevent.com/scl_electronics/gun/ultimaterapid/websize/trig-bush.jpg)
(https://photos.imageevent.com/scl_electronics/gun/ultimaterapid/websize/trig-bush4.jpg)
This will eliminate any sideways wobble!!
Gives you a more Precise Feel!!
Also you can use Ball-Bearing tip screws on the trigger arm....if you can find them..
(https://photos.imageevent.com/scl_electronics/gun/ultimaterapid/websize/trig-polish.jpg)
Or just file to round off the cup on the tip of the standard grub screw, and polish them!!!

Have Fun!!
Stuart



Wow, if only, that pure skill, something I'm rather short of I'm  😆