Hi all, i picked this FAC Mk 2 Rapid up this morning and im well chuffed with it. Ive dated it to 2001 and i think it has the Anschutz trigger. Its running at around 40 ftlbs and its doing sub 10 mm groups, albeit at only 10 metres. Its been standing unused for quite some time so now i'm looking for someone to give it a service before i take it out, any recommendations please?
Hi telbert.
That looks very nice and clean with an early mod fitted.
Im sure if your this side of the pond KevG can help you out.
Regards Kev.
Nice Trigger..sought by many as the Near Match Trigger....
I would go with KCE Recommendation..KevG
The Rapid's Best Friend!!
Good Luck with her.. It sound it is shooting Good.
Just needs it's O-rings check if it hasn't service for a Long Time!
Cheers M8,
Stuart
Quote from: Ca_Varminter on August 29, 2022, 07:02:38 PM
Nice Trigger..sought by many as the Near Match Trigger....
I would go with KCE Recommendation..KevG
The Rapid's Best Friend!!
Good Luck with her.. It sound it is shooting Good.
Just needs it's O-rings check if it hasn't service for a Long Time!
Cheers M8,
Stuart
Last time it was serviced was in 2011 when it was FAC tuned by PAX Guns. :o
So, is this likely to have a fast flow fitted rather than a reg? If so Would one of Kev G's reg's improve the performance?
Quote from: telbert on August 29, 2022, 07:13:05 PM
So, is this likely to have a fast flow fitted rather than a reg? If so Would one of Kev G's reg's improve the performance?
It all depends on what the Power level was turned up to!!
If was below 40fpe... it still could be regged..
Just take a look at the bottle adapter that screws into the Receiver!
If it has a small hole on the side near the receiver, then it Does have a Reg!
(https://photos.imageevent.com/scl_electronics/gun/air/image.gif)
Good Luck,
Stuart
have you actually seen it on chrono doing 40 ftlbs, thats alot if on the standard length fac 19 inch barrel, even on a fast flow.you have to be careful with the anschutz triggers and very high hammer load as the sears can snap.
KevG
Quote from: KevG on August 29, 2022, 09:34:39 PM
have you actually seen it on chrono doing 40 ftlbs, thats alot if on the standard length fac 19 inch barrel, even on a fast flow.you have to be careful with the anschutz triggers and very high hammer load as the sears can snap.
KevG
This Why KevG is the RapidMan!!!!
Good Catch!
Stuart
So, the info i now have : a reciept from Pax Guns dated 2011 for tuning to 40 ftlbs is in with the paperwork.I've taken the bottle and stock and it has 6 no holes in the bottle adapter and definitely no hole in the side of the adapter. It was doing 36ftlbs yesterday but now its down to 7/8 ftlbs.
Quote from: telbert on August 30, 2022, 10:14:59 AM
So, the info i now have : a reciept from Pax Guns dated 2011 for tuning to 40 ftlbs is in with the paperwork.I've taken the bottle and stock and it has 6 no holes in the bottle adapter and definitely no hole in the side of the adapter. It was doing 36ftlbs yesterday but now its down to 7/8 ftlbs.
Leaky bottle!!
just refilled the bottle and dropped it in a bucket of water and its got a leak, did the same to another bottle and its got an even smaller leak so ill need some info on fixing these too please, ill get some pics up shortly.
The rifle is now doing 39/40 ftlbs as shown
These are the 2 bottles that are leaking.The first pick has the slowest leak, didnt even notice it while i was using it,the second pick is the worst leak.
Quote from: telbert on August 30, 2022, 10:14:59 AM
So, the info i now have : a reciept from Pax Guns dated 2011 for tuning to 40 ftlbs is in with the paperwork.I've taken the bottle and stock and it has 6 no holes in the bottle adapter and definitely no hole in the side of the adapter. It was doing 36ftlbs yesterday but now its down to 7/8 ftlbs.
6 holes in the bottle push pin is a "fast flow" same as I've got on my .25 FAC,
If it was me I'd be looking to turn it down a fair bit to get a lighter pellet, running around 900fps and get more shots per fill, but that's just a personal preference.
A leaking bottle doesn't really mater while it's fitted to the rifle but not good if it's your spare, fixing it means taking the valve off the bottle to change the seal, make sure the bottle is vented first.
There should be no need for the PTFE tape on the bottles, the O ring is what seals it, you do know to "burp" the bottle (dry fire) as you remove it don't you ?
Quote from: angrybear on August 30, 2022, 11:26:13 AM
Quote from: telbert on August 30, 2022, 10:14:59 AM
So, the info i now have : a reciept from Pax Guns dated 2011 for tuning to 40 ftlbs is in with the paperwork.I've taken the bottle and stock and it has 6 no holes in the bottle adapter and definitely no hole in the side of the adapter. It was doing 36ftlbs yesterday but now its down to 7/8 ftlbs.
Thanks for the reply angrybear.
6 holes in the bottle push pin is a "fast flow" same as I've got on my .25 FAC,
If it was me I'd be looking to turn it down a fair bit to get a lighter pellet, running around 900fps and get more shots per fill, but that's just a personal preference.
Yes i want consistency & accuracy over power
A leaking bottle doesn't really mater while it's fitted to the rifle but not good if it's your spare, fixing it means taking the valve off the bottle to change the seal, make sure the bottle is vented first.
Agreed in the short term but i will need to change the seal eventually. Can i just remove the valve by hand once its completely empty? Do you know if there are any vids on youtube that cover this?
There should be no need for the PTFE tape on the bottles, the O ring is what seals it, you do know to "burp" the bottle (dry fire) as you remove it don't you ?
Yeah, i've been burping it while removing.Tbh the ptfe is on there for filling .I cant find my best fitting connector but had an old spare one laying about but it doesn't create a perfect seal.
Also with a fast flow, does this simply allow more air into the valve to increase power unregulated? Ifso i'm guessing the power would drop as the air in the bottle decreases until empty?
depends how its been turned and set up by rights from a full fill you should get a power curve,for example first shots around 900 climbing as bottle pressure drops to around 920 then back down to 900.if it just starts high then drops the gun is being thrashed and waisting air.if power as dropped that much you must have a leak somewhere
KevG
Quote from: KevG on August 30, 2022, 05:47:37 PM
depends how its been turned and set up by rights from a full fill you should get a power curve,for example first shots around 900 climbing as bottle pressure drops to around 920 then back down to 900.if it just starts high then drops the gun is being thrashed and waisting air.if power as dropped that much you must have a leak somewhere
KevG
So if i wanted to fit one of youre regs can the block be posted out to you for fitting/ setting up or could i fit it myself if i bought from you? Also whats the cost for this please?
no I could do a reg set to pressure for your gun,but with a reg and 21.4 grn pellets you would be better running around 840 fps.you would need to adjust hammer pre load spring tension to suite the reg.if I was you I would use the gun first and see how it goes before spending money on it m8
KevG
Quote from: telbert on August 30, 2022, 12:45:50 PM
Quote from: angrybear on August 30, 2022, 11:26:13 AM
Quote from: telbert on August 30, 2022, 10:14:59 AM
So, the info i now have : a reciept from Pax Guns dated 2011 for tuning to 40 ftlbs is in with the paperwork.I've taken the bottle and stock and it has 6 no holes in the bottle adapter and definitely no hole in the side of the adapter. It was doing 36ftlbs yesterday but now its down to 7/8 ftlbs.
Thanks for the reply angrybear.
6 holes in the bottle push pin is a "fast flow" same as I've got on my .25 FAC,
If it was me I'd be looking to turn it down a fair bit to get a lighter pellet, running around 900fps and get more shots per fill, but that's just a personal preference.
Yes i want consistency & accuracy over power
A leaking bottle doesn't really mater while it's fitted to the rifle but not good if it's your spare, fixing it means taking the valve off the bottle to change the seal, make sure the bottle is vented first.
Agreed in the short term but i will need to change the seal eventually. Can i just remove the valve by hand once its completely empty? Do you know if there are any vids on youtube that cover this?
There should be no need for the PTFE tape on the bottles, the O ring is what seals it, you do know to "burp" the bottle (dry fire) as you remove it don't you ?
Yeah, i've been burping it while removing.Tbh the ptfe is on there for filling .I cant find my best fitting connector but had an old spare one laying about but it doesn't create a perfect seal.
Also with a fast flow, does this simply allow more air into the valve to increase power unregulated? Ifso i'm guessing the power would drop as the air in the bottle decreases until empty?
How tight the bottle valve is depends if it's ever been off before & if/how much, thread-lock has been used,
they don't just fall out, but with the bottle in a vice (with soft jaws) a ring spanner on the valve, a quick whack should shift it, always has with mine.
Someone will correct me if wrong,
but a fast flow allows air from the bottle in to the prechamber faster (as per the name) so the pressure doesn't drop, over the time a shot takes,
this means the balance between exhaust valve, barrel port & hammer strike, control the efficiency, limiting wasted air behind the pellet & the power curve.
A FF barrel has a smaller port than a regulated barrel to limit the air flow at max pressure in order to reduce the power curve as the bottle pressure drops.
A regulator limits the max pressure in the pre-chamber by shutting the bottle off so every shot has the same pressure, the barrel port can be opened to speed airflow,
& the valve better tuned to the hammer strike because it doesn't have to cope with varying pressures, so it's more efficient.
Quote from: angrybear on August 30, 2022, 10:56:40 PM
Quote from: telbert on August 30, 2022, 12:45:50 PM
Quote from: angrybear on August 30, 2022, 11:26:13 AM
Quote from: telbert on August 30, 2022, 10:14:59 AM
So, the info i now have : a reciept from Pax Guns dated 2011 for tuning to 40 ftlbs is in with the paperwork.I've taken the bottle and stock and it has 6 no holes in the bottle adapter and definitely no hole in the side of the adapter. It was doing 36ftlbs yesterday but now its down to 7/8 ftlbs.
Thanks for the reply angrybear.
6 holes in the bottle push pin is a "fast flow" same as I've got on my .25 FAC,
If it was me I'd be looking to turn it down a fair bit to get a lighter pellet, running around 900fps and get more shots per fill, but that's just a personal preference.
Yes i want consistency & accuracy over power
A leaking bottle doesn't really mater while it's fitted to the rifle but not good if it's your spare, fixing it means taking the valve off the bottle to change the seal, make sure the bottle is vented first.
Agreed in the short term but i will need to change the seal eventually. Can i just remove the valve by hand once its completely empty? Do you know if there are any vids on youtube that cover this?
There should be no need for the PTFE tape on the bottles, the O ring is what seals it, you do know to "burp" the bottle (dry fire) as you remove it don't you ?
Yeah, i've been burping it while removing.Tbh the ptfe is on there for filling .I cant find my best fitting connector but had an old spare one laying about but it doesn't create a perfect seal.
Also with a fast flow, does this simply allow more air into the valve to increase power unregulated? Ifso i'm guessing the power would drop as the air in the bottle decreases until empty?
How tight the bottle valve is depends if it's ever been off before & if/how much, thread-lock has been used,
they don't just fall out, but with the bottle in a vice (with soft jaws) a ring spanner on the valve, a quick whack should shift it, always has with mine.
Someone will correct me if wrong,
but a fast flow allows air from the bottle in to the prechamber faster (as per the name) so the pressure doesn't drop, over the time a shot takes,
this means the balance between exhaust valve, barrel port & hammer strike, control the efficiency, limiting wasted air behind the pellet & the power curve.
A FF barrel has a smaller port than a regulated barrel to limit the air flow at max pressure in order to reduce the power curve as the bottle pressure drops.
A regulator limits the max pressure in the pre-chamber by shutting the bottle off so every shot has the same pressure, the barrel port can be opened to speed airflow,
& the valve better tuned to the hammer strike because it doesn't have to cope with varying pressures, so it's more efficient.
Thanks for all this info angrybear.
Quote from: KevG on August 30, 2022, 08:25:25 PM
no I could do a reg set to pressure for your gun,but with a reg and 21.4 grn pellets you would be better running around 840 fps.you would need to adjust hammer pre load spring tension to suite the reg.if I was you I would use the gun first and see how it goes before spending money on it m8
KevG
Thanks Kev, yeah i'll need to get out with the rifle a few times first to see how its behaving before i decide the next move.
Telbert, is this the one I pointed out to you from Wales
Quote from: Kevgun on September 01, 2022, 09:23:37 AM
Telbert, is this the one I pointed out to you from Wales
No this one came from your neck of the woods Kev.
I actually drove past Doncaster on the way home.
Wrong KevG, Im in Basingstoke ;D
one of us needs to change our name kev m8😁
.