Theoben Rapid Forum

Theoben General Chat Area => Theoben Rapid Discussion => Topic started by: smithy123 on July 14, 2022, 03:20:05 PM

Title: Best fitting valve removal
Post by: smithy123 on July 14, 2022, 03:20:05 PM
I finally managed to get a dr bob valve for my cf bottle but I'm struggling to get it off I have tried shocking it but will not budge can anyone give me some advise please
Title: Re: Best fitting valve removal
Post by: Ca_Varminter on July 14, 2022, 04:51:35 PM
Hopefully there is No thread-locker/sealant Used...
Also since it is a CF bottle.... Protection of the surface is Important!
What I do is use a bench vise. I have cut a pair of wooden blocks to fit.
Then I wrap the CF bottle with rubber...a strip of rubber inner-tube works well.
Since it has flats milled into it... Use a proper fitting wrench.
A cheater bar might be needed..
Secure the bottle in the vice and give a good YANK!
This should break it free.... it has always worked for Me!

Good Luck,
Stuart
Title: Re: Best fitting valve removal
Post by: Robs5230 on July 14, 2022, 07:06:54 PM
This isnt going to help, but a mate asked me if I'd remove the valve on his BF carbon bottle for the same reason.
I couldn't budge it.
He's going to have to have to have it back with the standard valve on it
Title: Re: Best fitting valve removal
Post by: Daztilley on July 14, 2022, 07:11:29 PM
I use a 60mm hydraulic hose clamp to hold the bottle safely in the vice
The inside of the clamp is rubber so it grips the bottle around the full circumference and prevents any damage - never failed to remove a valve 👍
Title: Re: Best fitting valve removal
Post by: Daztilley on July 14, 2022, 07:14:46 PM
Same as this type ( in the pic )
50mm for 200cc and 280cc
60mm for 400cc  and 500cc and most carbon bottles
Title: Re: Best fitting valve removal
Post by: Ca_Varminter on July 14, 2022, 07:18:56 PM
Nice One Daz!!
I never thought of those guys....
I seen them before..... Just never made the Connection!!!! ??? ??? ???
;) ;) ;) ;) ;) ;) ;) ;) ;)

Stuart
Title: Re: Best fitting valve removal
Post by: Daztilley on July 14, 2022, 07:23:12 PM
They are really useful for stripping air tube ends too - you just need the correct size

They are cheap and you only need to buy em once 👍
Title: Re: Best fitting valve removal
Post by: angrybear on July 14, 2022, 07:29:14 PM
What you can try is a "tourniquet wrench" but I don't know if it could damage the surface.

Put the valve flats in a vice.
Wrap a 36" rope loop, in 3 loose loops around the bottle, stick a steel crowbar about 6" through the loops & twist it
This will tighten up on the bottle like a tourniquet, when it's as tight as you can get it, use the loops as the cushion for the short end of the bar, & the long end as the handle to twist.
Title: Re: Best fitting valve removal
Post by: Ca_Varminter on July 14, 2022, 07:49:47 PM
Personally I have never had very good Luck with those "Strap" wrenches when the valve is very Tight....
Also I don't like the single pressure/pivot point of those "Strap" wrenches....
Sort of like what you see when you Use one on an oil filter!!
So I liken distributing the pressure over the circumference of the bottle..
Like when I use wooden blocks or Daz's hydraulic clamps...

Stuart
Title: Re: Best fitting valve removal
Post by: angrybear on July 15, 2022, 08:47:30 AM
I agree, but needs must,
when you don't have the correct tool you use what you have.  ;)
Title: Re: Best fitting valve removal
Post by: Squinty on July 15, 2022, 09:53:27 AM
I've had the valves out of my Inocoms a few times.

I wrap the bottle in an old piece of boot leather and put it in the vice with an extra layer of rubber mat
Also made some soft jaw faces from some old flashing.. couldn't find the other one for the pictures.
I don't like the flats on BF valves, I think the 1" hex on Bob's are much better as I can get a socket on and use a torque wrench to tighten accurately.. not just hang on a spanner.
I have BSA valves on these, Kev made some PEEK pips for them.
No leaks.

Title: Re: Best fitting valve removal
Post by: smithy123 on July 15, 2022, 12:08:06 PM
Thanks squinty, what I did was get the valve end in the vice, put some insulation tape just avoided the neck and made a big loop in some small ratchets strap rope and rapped it around and put a bar in to use as leverage and it come straight off no issues!!

I tried shocking it with hammer and spanner but was getting nowhere lol so yeah all done now and back on the gun