Theoben Rapid Forum

Theoben General Chat Area => Theoben Rapid Discussion => Topic started by: Simonoxo on April 22, 2022, 12:30:23 AM

Title: Trigger options?
Post by: Simonoxo on April 22, 2022, 12:30:23 AM
Any recommendations on trigger upgraded over standard mk1 trigger I think mine has gamo one on not majorly bad but feels a little numb to what I'm used to on shotguns.
Title: Re: Trigger options?
Post by: Ca_Varminter on April 22, 2022, 01:04:21 AM
KevG is your man...
He may be able to work a little of his Magic, a bit of polishing, and even a bearing..
Then there is also Dr Bob.
Dr Bob used make a replacement trigger lever..
Something like what Charlie DaTuna makes...
https://www.charliedatuna.com/

Good Luck
Stuart
Title: Re: Trigger options?
Post by: Simonoxo on April 22, 2022, 01:49:14 AM
Thanks Stuart
I'll have a look hard to explain how this one is it's just not as snappy as I'd like
Title: Re: Trigger options?
Post by: Ca_Varminter on April 22, 2022, 02:19:56 AM
No need to explain.....
The stock Gamo trigger is Mushy!!!!!
I have Custom trigger on most my Rifles... Air and Powder.
There is nothing like a crispy breaking Two stage trigger...
Even though my Custom 22-250 has a single set, single stage trigger!!

This also the reason all my Rapid are MKII. The Mark4 trigger is almost Match trigger...

Stuart
Title: Re: Trigger options?
Post by: Simonoxo on April 22, 2022, 04:01:16 AM
Awsome thanks for info. So would I be better off looking for a newer trigger assembly all together rather then just swapping out the trigger? Is that somthing I could do
Title: Re: Trigger options?
Post by: Ca_Varminter on April 22, 2022, 05:53:14 AM
Well that is easier said than done!!
With the MKI you have don't have many options...
Trying to improve the existing Gamo trigger.
Try to find a working Gold Medal trigger Group.....Nearly impossible...

The last one is a longshot...
If you can find a good machinist/gunsmith.
You can machine your existing block to accept the Mark4 trigger!
I personally know the only gunsmith over on my side of the Pond that does this conversion on all Rapids!
My first Rapid a MKII with a sporter trigger, was the test subject for this conversion!
After this success, he spoke to Theoben about this. Soon after, they offered this Service!!!!!

Good Luck again...
Stuart
Title: Re: Trigger options?
Post by: Simonoxo on April 22, 2022, 08:54:24 AM
I run a fanuc dahlih for a living 😊lots of odd ball parts daily something I can have a look at in future. Think I'll stick easy option on first see if it improves it any.
Thanks again Stuart your a wealth of knowledge 🍻
Title: Re: Trigger options?
Post by: Squinty on April 22, 2022, 09:45:25 AM
A Gamo trigger can be improved however its a single stage unit- the long pull and heavy spring is a false 1st.

The pull weight is down to the trigger return spring, a simple 90* lever spring. That can be bent to reduce weight -trial and error.
Springs out of later generic units are mostly heavier, you can find stock lever springs at various suppliers..0.6-0.75mm wire but so far I haven't tried any.

The length of pull can be shortened by fitting a bush or RC micro-bearing on the trigger pin 15L
Once you lose the excess travel the trigger becomes much more positive and its easier to pull through rather than anticipating the break.

Besides that...a good polish up on all the sear faces and that's about it.
Title: Re: Trigger options?
Post by: KevG on April 22, 2022, 05:41:29 PM
I got some of the thinner section return spring made up and fited a few delrin bushes,along with a trigger shoe it can make the crapy gamo unit very nice
KevG
Title: Re: Trigger options?
Post by: Simonoxo on April 22, 2022, 08:49:32 PM
Quote from: KevG on April 22, 2022, 05:41:29 PM
I got some of the thinner section return spring made up and fited a few delrin bushes,along with a trigger shoe it can make the crapy gamo unit very nice
KevG
Do you sell these if so I'd be interested payday Monday :-)
Title: Re: Trigger options?
Post by: KevG on April 23, 2022, 01:02:15 PM
the bush is not something you can just send out as individual triggers can respond differently, it also depends on how much travel an individual trigger as some times you have to make a few bushes to get how you want it
KevG