Theoben Rapid Forum

Theoben General Chat Area => Theoben Rapid Discussion => Topic started by: Squinty on March 07, 2022, 11:26:56 AM

Title: hanging by a thread
Post by: Squinty on March 07, 2022, 11:26:56 AM
guess that's knackered  ???
Title: Re: hanging by a thread
Post by: Andycoup on March 07, 2022, 11:31:29 AM
 :oI?d say so!!!

What?s the thread in the reg like?
Title: Re: hanging by a thread
Post by: nevadacowboy on March 07, 2022, 11:40:08 AM
Think you need to visit Best Fittings. They have both standard and MFR bottle valves.
Title: Re: hanging by a thread
Post by: Squinty on March 07, 2022, 11:42:40 AM
the reg is fine.. it was a brass BSA superten valve that came with my mk1 20.

Title: Re: hanging by a thread
Post by: Squinty on March 07, 2022, 11:45:46 AM
Quote from: nevadacowboy on March 07, 2022, 11:40:08 AM
Think you need to visit Best Fittings. They have both standard and MFR bottle valves.

Bob's?  Job done
Title: Re: hanging by a thread
Post by: KCE on March 07, 2022, 12:02:40 PM
What would cause that problem?

Regards Kev.
Title: Re: hanging by a thread
Post by: Squinty on March 07, 2022, 12:40:03 PM
to start with it's an old  valve, probably 20 years since BSA used those and I have no idea of its history.
Supetens were brass on brass not stainless like Rapids.

Could have been over tightened, I know that some Theoben bottle holders had a wider push pin that BSA bottles smaller outlet wouldn't go over.
Maybe spent some time on a tight/sharp bottle holder which has further stressed the thread.. it is brass.

I have new BSA brass valves on my FAC bottles and the the gun had BSA valves modified by AWT before that.
They lasted 12-13 years and only replaced those because I had to cut them off the bottles after they leaked.
Title: Re: hanging by a thread
Post by: Ca_Varminter on March 07, 2022, 03:00:19 PM
Time for a Dr Bob bottle Valve!!
Brass is NOT my first choice for High Air Pressure fittings!!
(https://photos.imageevent.com/scl_electronics/gun/air/websize/valve2.jpg)

Stuart
Title: Re: hanging by a thread
Post by: Squinty on March 07, 2022, 03:05:21 PM
already done  ;)







Title: Re: hanging by a thread
Post by: Ca_Varminter on March 07, 2022, 05:24:43 PM
How about a Dr Bob Bottle Cap!!
It seal on the Bottle O-ring!!
(https://photos.imageevent.com/scl_electronics/gun/air/websize/bottlecap.jpg)

Stuart
Title: Re: hanging by a thread
Post by: Squinty on March 07, 2022, 05:42:21 PM
how about 2.99 for 5 pipe caps?
Title: Re: hanging by a thread
Post by: angrybear on March 07, 2022, 09:22:30 PM
That's not a Helicoil is it  :o
You've got to go some to take a complete thread off like that  ??? that's a five white knuckles job  :-[
Title: Re: hanging by a thread
Post by: Squinty on March 07, 2022, 11:41:04 PM
Quote from: angrybear on March 07, 2022, 09:22:30 PM
That's not a Helicoil is it  :o
You've got to go some to take a complete thread off like that  ??? that's a five white knuckles job  :-[

Nope, it sure ain't a helicoil.

The bottle /valve came with my mk1 20, I'd hadn't used it and kept it as a spare.
As previously mentioned - no idea of the history.

Rather than take one of the c/f bottles of my other Rapids I used it to check the reg.
I unscrewed the bottle 1-1/8 turns before purging the tester and POP.
To start with I thought it was the o-ring going a bit early.

if it had gone 15 minutes earlier when I topped up to 200bar..that might have been a clean pants moment  :o
Title: Re: hanging by a thread
Post by: phil.m on March 09, 2022, 02:10:51 PM
From the thumbnail, I thought "why put a spring in there?"

Then I clicked on the picture.  :o

Glad you're fine & the bottle isn't in a neighbor's living room wall  ;)