Theoben Rapid Forum

Theoben General Chat Area => Theoben Rapid Discussion => Topic started by: Andycoup on January 02, 2022, 05:34:28 PM

Title: Hammer pip
Post by: Andycoup on January 02, 2022, 05:34:28 PM
Hi folks, hope you're all enjoying your new year bank holiday weekend.

I recently aquired rapid number 4, which had been 'modded'. The pip has been (quite crudely) shortened.

Is the pip removable from the hammer? And if so, is it threadlocked in?

The gun is a late block, mk4 trigger, if that helps.

Cheers, Andy.
Title: Re: Hammer pip
Post by: Rapid7bee on January 02, 2022, 06:08:38 PM
Yes,just heat up the top/tip with a blowtorch until you smell the glue/loctite
burning. Unsrew when hot as much easier, I done my last night.
Title: Re: Hammer pip
Post by: alan1 on January 03, 2022, 11:20:29 AM
There should be information about pip leights for sub 12 and fac and people who can supply one
Title: Re: Hammer pip
Post by: Squinty on January 03, 2022, 12:41:01 PM
there's barely a handful of people who make and supply parts exclusively for Rapids and a few good lathe guys that may come to the rescue if asked.
otherwise take your pick and ask one of the known airgun tuners.... who might make a pip if not too busy.

...even a 2ba bolt (and locknut) the right length will do the job ;)

15-17mm sub-12
6-10mm for the others
Title: Re: Hammer pip
Post by: Andycoup on January 03, 2022, 01:07:39 PM
Making a pip shouldn't be too much of a problem, I have access to a lathe.

I think I measured the length of the pip at 12mm, so it definitely needs lengthening. I'll probably do a silent pip.

Andy.
Title: Re: Hammer pip
Post by: KevG on January 03, 2022, 02:06:25 PM
between 16 and 17 mm for sub 12ftlbs. 2BA thread length of thread 14mm.this is critical on thread length as you need it to extend slightly into the hammer chamber for the inertia spring to sit on.other wise is will distort and break
KevG
Title: Re: Hammer pip
Post by: alan1 on January 04, 2022, 12:38:14 PM
Yes I found out the hard way when I made my first pip with a short thread and damaged the spring and did not know at time it was due to that
Title: Re: Hammer pip
Post by: alan1 on January 08, 2022, 10:31:18 AM
Hi do R A W use a hammer with a pip with no thread sticking through
Title: Re: Hammer pip
Post by: Aggy on January 08, 2022, 01:18:02 PM
The Raw is all one piece not adjustable
Title: Re: Hammer pip
Post by: KevG on January 08, 2022, 01:35:48 PM
earlier Raws were threaded hammers like the theoben/impacts
KevG
Title: Re: Hammer pip
Post by: alan1 on January 08, 2022, 03:41:05 PM
So how does the inatia spring not get damaged
Title: Re: Hammer pip
Post by: KevG on January 08, 2022, 03:50:15 PM
it can do.did one last week what had the one piece hammer and that spring was buckled.
KevG
Title: Re: Hammer pip
Post by: KevG on January 08, 2022, 04:12:36 PM
its not just the latest Raws that have the one piece hammers.they were also on the first Airforce ones to.
KevG
Title: Re: Hammer pip
Post by: Ca_Varminter on January 08, 2022, 04:47:19 PM
Quote from: alan1 on January 08, 2022, 03:41:05 PM
So how does the inatia spring not get damaged

First WHY it Happens ....
The small Inertia weight uses the threaded potion of the Inertia Weight  as a Spring Guide and Striker!
If there isn't enough of the Threaded Portion Exposed, the Inertia(anti-rattle) Spring will Pound itself into Dust!!

HOW to Prevent this from happening...
1. If you're replacing your Pip.
    Compare the Threaded portions between the old one and New, making it is not too short!!
2.Make sure you apply a little Loctite to the new pip.... It can back out.. Causing the same condition as Above!

Stuart
Title: Re: Hammer pip
Post by: Aggy on January 08, 2022, 04:58:12 PM
My New spec Raw has a small projection at the inside front of the hammer ,guess it must be either a pressed in piece or machined in ?
Title: Re: Hammer pip
Post by: KevG on January 08, 2022, 05:18:12 PM
thats pressed in.some have this and some don't
KevG
Title: Re: Hammer pip
Post by: KevG on January 08, 2022, 09:01:47 PM
here is a Raw fixed hammer
KevG
Title: Re: Hammer pip
Post by: alan1 on January 09, 2022, 08:38:20 AM
Could you then put a small spring gide in then
Title: Re: Hammer pip
Post by: Andycoup on January 10, 2022, 07:32:33 PM
When making a silent pip with peek, does it need to be an insert, or can the whole pip be plastic?

Andy.
Title: Re: Hammer pip
Post by: KevG on January 10, 2022, 08:43:50 PM
yes you could do but I make the thread and case out of stainless. then delrin insert. no need for expensive peek.
KevG