Theoben Rapid Forum

DrBob`s products & parts => Dr Bob's Section => Topic started by: Dr Bob on October 29, 2021, 05:08:03 PM

Title: Barrel location screws
Post by: Dr Bob on October 29, 2021, 05:08:03 PM
One of the tasks I set Alex the new guy were these. Passed with flying colours.  They are going to be £12.50 each as they are a sod to make.  He even milled the hex in the top.
Title: Re: Barrel location screws
Post by: Ca_Varminter on October 29, 2021, 08:00:19 PM
They Look Fabulous!!!
So are made out of Stainless....
I will take 5 for my parts box!!

Let me know how much for shipping and handling to this side of the pond...
Also add a little, for a trip to the Pub with Fran!!

Stuart
Title: Re: Barrel location screws
Post by: Dr Bob on October 30, 2021, 09:56:09 AM
Silver steel is harder than stainless as standard but can be hardened further. BTW the thread is M7x.75 outside and 2BA inside.
Bob
Title: Re: Barrel location screws
Post by: etiam viviens on October 30, 2021, 11:01:53 PM
Very nice  ;D
If correct 2 of these are going my way with 3 dogs.

Title: Re: Barrel location screws
Post by: etiam viviens on November 13, 2021, 03:48:41 PM
Just received the dogs and the location screw ;D

Got my .22 shooting again and remove that piece of plastic that was hammered in the .25 instead of the screw.

Thanks for making these Bob :)
Title: Re: Barrel location screws
Post by: Dr Bob on November 23, 2021, 04:42:54 PM

Did Theoben do another thread ? I have been asked for M6 but no way can you get a 2BA thread in that.

Bob
Title: Re: Barrel location screws
Post by: Ca_Varminter on November 23, 2021, 05:33:47 PM
KevG is the Expert....
But as far as I know...... No.....

How Are things Dr Bob??
Say hi to Fran from me!

Stuart
Title: Re: Barrel location screws
Post by: angrybear on November 23, 2021, 11:11:49 PM
Quote from: Dr Bob on November 23, 2021, 04:42:54 PM

Did Theoben do another thread ? I have been asked for M6 but no way can you get a 2BA thread in that.

Bob

Could be just a slip of the key board, judging by what I read few people either proof read or bother to correct the gibberish they post or email.
Title: Re: Barrel location screws
Post by: Dr Bob on November 24, 2021, 02:44:18 PM

No they sent me a sample. It's just a grub screw with no internal thread, so he can't fit my dovetail rail. If that's the case he can line up the barrel with the grub screw nip the clamp up then fit a countersunk M6 screw to fit the dovetail??

Bob
Title: Re: Barrel location screws
Post by: Ca_Varminter on November 24, 2021, 04:33:57 PM
Well Dr Bob,
You can always cheat... If he sent you his Rapid....
Remember I re drilled my rapids to use my 2 piece picatinny rails!!
(https://photos.imageevent.com/scl_electronics/gun/air/websize/scope-holes.jpg)

Drill and tapped for 10-32 unf cap screws

Stuart
Title: Re: Barrel location screws
Post by: Squinty on November 26, 2021, 07:32:24 PM
three ordered yesterday and received today
thanks for the fast service Bob