Would anyone have a guide for stripping/rebuilding the mk 3 trigger please ?
I've been through all guides I can see on here & sadly nothing on the mk 3
I think the one that came with the block is missing a pin as there are 3 holes in a diagonal row & the middle hole is empty ?
I have limited experience with them... Mostly changing them out!!
Here is the Theoben's instruction sheet....
(https://photos.imageevent.com/scl_electronics/gun/air/websize/Mark%203.jpg)
Ask KevG, he has played with them.....
Stuart
Thanks Stuart that's fantastic.
I'm obviously missing the sear stop pin, & by the look there should be a spring & ball under the 2nd stage weight adjuster, also missing,
& the2nd stage let off screwed into the stop, rounded & jammed solid which explains why I can't get it to do owt ???
In short probably a bin job :(
I don't suppose they're a straight swap with a mk 4 are they ?
Well Yes and no....
The Mark 4 cartridge will fit no Problem...
BUT the hammer needs to be changed....
I know Dr Bob is out of triggers.. but may still have Hammers!!
Good Luck,
Stuart
some of the mk3 trigger hammers are compatible with the serries 4 triggers.best way to check is the angle of the hammer were the sear contacts.those what can cause problems are the angled sear contact type.i maybe able to help with the part you have missing on your 3 trigger.
KevG
Many thanks Kev,
The sear in mine looks exactly like the one in the above picture.
As for missing bits, there's no sear stop pin, the sear spring seems too short to tension on anything so I think that needs replacing,
There is no spring or ball to adjust the front screw 2nd stage weight (although there was the remains of a tiny spring inside the cassette)
It looks to me as if there should be a ball to locate the safety 'on'
and I suspect the killer is the rear 'let off' screw which is graunched all the way in & rounded.
If you could take a look at it I'd appreciate it.
Steve.
here is a picture of one of mine.the only spring and ball on these triggers is what aids the indexing of the safety.very small spring removed with the very small ball bearing for viewing purposes
KevG
Some pic's,
Kev surely there's also a spring at the front of the strut that screw D tensions ? I think I can just see it in your pic,
my screw A being shagged & jammed strikes me as the main problem.
looks like the rubber oring is on the wrong side to.
KevG
yes it should have a spring on screw D but no ball.the only spring and ball is on safety
KevG
if you look at mine you can just see the spring in D
KevG
The O ring is down to me, I used it to hold the catch in place,
So I need;
1/ sear stop pin, 2/sear spring, 3/ safety catch ball & spring, 4/ strut spring.
Would you sell them or have any idea where I can get them ??
If I can at least get it functioning I'll worry about the 2nd stage let off later.
Steve.
I would have to get the springs made as no spares for these triggers now.not sure were you would get a ball from that size.i guess someone must do them some were m8.
KevG
So I'm pretty much back to square 1, needing a replacement trigger unit ::)
think I may have a full working trigger some were.
KevG
Well it isn't a Complete Waste Bin trigger (Trash Trigger)
For the safety detent ... You just need to find a spring and small ball-bearing
that fits into the hole of the safety lever.....
a local bearing and seal supplier my have something that will work.
In a pinch, for the ball-bearing, you can machine a plunger out of brass or stainless steel..
Stuart
Sadly I have no machining facilities Stuart.
Thanks Kev,
I think I'm actually sorted, the chap who sold me the block has been in touch & offered a replacement cassette as he thought the one fitted was good.
Good news - glad guy helped you out 👍
thats a good result.nice one.
KevG
Now all sorted with a mk4 thanks to Guy,
If the remains of the mark 3 is any use to someone, you know where it is.