Theoben Rapid Forum

Theoben General Chat Area => Theoben Rapid Discussion => Topic started by: Foxdropper on August 11, 2021, 06:51:24 PM

Title: Re non firing
Post by: Foxdropper on August 11, 2021, 06:51:24 PM
Doing my head in 😞Took the rapid outlast night and fired a few decent groups .Back out this evening and damn thing won't fire .Filled bottle so not an issue ,not tweaked anything just won't fire .Any suggestions please .Phone number can be supplied if needed .
Regards FD
Title: Re: Re non firing
Post by: KevG on August 11, 2021, 07:32:26 PM
what do you mean by not firing.is it cocking .
KevG
Title: Re: Re non firing
Post by: Foxdropper on August 11, 2021, 08:03:03 PM
Bolt goes back and forward under pressure as I remember .Safety off and nothing on firing mate .Cant see I'm doing anything stupid as they are basic and bomb proof and had pcp all my shooting life .Any chance of a chat via phone mate ?
Title: Re: Re non firing
Post by: Kernal on August 11, 2021, 08:06:57 PM
Quote from: Foxdropper on August 11, 2021, 08:03:03 PM
Bolt goes back and forward under pressure as I remember .Safety off and nothing on firing mate .Cant see I'm doing anything stupid as they are basic and bomb proof and had pcp all my shooting life .Any chance of a chat via phone mate ?

If KevG does that M8 we other`s that follow this will not know what happened or how to fix the problem, I think you should both do this on an open thread,

If you both don`t mind that is!

;)
Title: Re: Re non firing
Post by: Foxdropper on August 11, 2021, 08:09:26 PM
No probs with that mate ,I just want to use the thing for what it was bought for .
Also both springs gone in mags 🤬
Title: Re: Re non firing
Post by: Kernal on August 11, 2021, 08:14:30 PM
Quote from: Foxdropper on August 11, 2021, 08:09:26 PM
No probs with that mate ,I just want to use the thing for what it was bought for .
Also both springs gone in mags 🤬

We also have Ca_Varminter how is really good with rapids to take the strain off KevG,...But also lots of other on here too who can help!

:)
Title: Re: Re non firing
Post by: KevG on August 11, 2021, 08:23:16 PM
when you pull bolt back is it leaving hammer behind in rear cock position as it should or is bolt coming back forward under pressure from hammer.if so trigger is not catching hammer so needs the little grub screw behind blade adjusting.it will need turning out anticlockwise 1/4 turn a time and test.
KevG
Title: Re: Re non firing
Post by: Foxdropper on August 11, 2021, 08:31:16 PM
Sorry Kev ,I must seem a right a right div but what hammer ? Does anyone know a tech guy off here in Wiltshire please .
If it makes any sense ,there is no pressure on the bolt either forward or back ,only to lock bolt open .I'm sure yesterday there was slight pressure on bolt going forward into mag .
I now have a pellet in barrel 🤬
Title: Re: Re non firing
Post by: Kernal on August 11, 2021, 08:35:00 PM
Quote from: Foxdropper on August 11, 2021, 08:31:16 PM
Sorry Kev ,I must seem a right a right div but what hammer ? Does anyone know a tech guy off here in Wiltshire please .

M8 i know you think it need`s sorting out asap,...But lets take a step back and go through it,....Let`s see what`s happening and let everyone else read the comment so if it happen`s to them they know just what to do as well,

:)
Title: Re: Re non firing
Post by: KevG on August 11, 2021, 08:35:30 PM
on about firing hammer.just adjust grub screw and try.should be 1.5mm xkey
KevG
Title: Re: Re non firing
Post by: KevG on August 11, 2021, 08:37:51 PM
if you had a magazine in when problem first developed you also could have shoved a few pellets up the barrel.in extreme cases this could cause a blocked up barrel.
KevG
Title: Re: Re non firing
Post by: Kernal on August 11, 2021, 08:43:55 PM
Quote from: Foxdropper on August 11, 2021, 08:31:16 PM
Sorry Kev ,I must seem a right a right div but what hammer ? Does anyone know a tech guy off here in Wiltshire please .
If it makes any sense ,there is no pressure on the bolt either forward or back ,only to lock bolt open .I'm sure yesterday there was slight pressure on bolt going forward into mag .
I now have a pellet in barrel 🤬

Your not a div m8, you have a problem that need solving and thats what this forum was created for,  But if you and KevG phone each other up about this problem then other`s that read the thread cannot see the out come and how it was resolved,

So it`s best if you both keep it on open thread so others can view and read so if it happens to them they can see how to fix this issue,

Ps you can add your own personal video`s to show indepth views of the problem involved!

;)

:)
Title: Re: Re non firing
Post by: Foxdropper on August 11, 2021, 08:54:26 PM
Ok so backing off the screw dosnt work chaps .Given it 7 quarter turns now and nothing .
Title: Re: Re non firing
Post by: Kernal on August 11, 2021, 08:56:29 PM
Quote from: Foxdropper on August 11, 2021, 08:54:26 PM
Ok so backing off the screw dosnt work chaps .Given it 7 quarter turns now and nothing .

Take pics M8 show KevG what your doing upload them to the forum M8,.

;)
Title: Re: Re non firing
Post by: Foxdropper on August 11, 2021, 09:02:19 PM
Quote from: Kernal on August 11, 2021, 08:43:55 PM
Quote from: Foxdropper on August 11, 2021, 08:31:16 PM
Sorry Kev ,I must seem a right a right div but what hammer ? Does anyone know a tech guy off here in Wiltshire please .
If it makes any sense ,there is no pressure on the bolt either forward or back ,only to lock bolt open .I'm sure yesterday there was slight pressure on bolt going forward into mag .
I now have a pellet in barrel 🤬

Your not a div m8, you have a problem that need solving and thats what this forum was created for,  But if you and KevG phone each other up about this problem then other`s that read the thread cannot see the out come and how it was resolved,

So it`s best if you both keep it on open thread so others can view and read so if it happens to them they can see how to fix this issue,

Ps you can add your own personal video`s to show indepth views of the problem involved!

;)

:)
All good mate but I bought the gun for a purpose for a job that is time specific .I'm very willing to travel a bit to someone who knows their stuff .Saturday is my dead line or it's a contract lost .No pressure then eh 😊
I'm also willing to post an in depth reply to how it was resolved but right now I need it working or good bye feral contract .
Need to set up scope properly as well .Two days might seem long  time but not when I work 12 hour days it isn't .
The forum will survive I'm sure without a drawn out diagnostics trying to teach me about something I know very little about .
Regards FD
Title: Re: Re non firing
Post by: Kernal on August 11, 2021, 09:09:14 PM
I would have liked this to be step by step, ?.... But i do understand your problem so maybe KevG will pm you and give you a step by step guide to fix the problem,

Good luck foxdropper,

Just would have like to see how this went on the forum open thread so other`s could have followed it and maybe just maybe if this happened to them,...well you know!

take care

I do hope you sort the problem out soon!

:)
Title: Re: Re non firing
Post by: Squinty on August 11, 2021, 09:19:24 PM
If you're undoing  the trigger adjuster (lefty-loosey) then thats going to increase the trigger pressure, perhaps to the point where it wont release.
Maybe the trigger shoe is stopping it from getting to the new break point?

Dodgy situation now...pellet/pellets up the spout and trigger jammed.
Ideally you need to apply the safety -lock the bolt back and clear the barrel.

errrr....its a three handed job to.....
hold bolt  in cocked but not locked back (down) position
screw in adjuster
and pull trigger.

without putting a hole in wall/ceiling /window

Title: Re: Re non firing
Post by: Squinty on August 11, 2021, 09:24:19 PM
part 7 is the hammer, if that is still locked back after cycling the bolt and the bolt is no longer under tension from the hammer spring .....then the trigger sear doesn't appear to be disengaging.

(https://i.imgur.com/2zSMbIc.jpg)

Title: Re: Re non firing
Post by: KCE on August 11, 2021, 09:26:33 PM
Thank you squinty much appreciated.

Regards kev.
Title: Re: Re non firing
Post by: KevG on August 11, 2021, 09:28:36 PM
the mk1 gamo can have alot of travel.if your brake point is far back the trigger shoe could be causing the problem like Stuart has already said
KevG
Title: Re: Re non firing
Post by: Foxdropper on August 11, 2021, 09:30:59 PM
Quote from: Squinty on August 11, 2021, 09:19:24 PM
If you're undoing  the trigger adjuster (lefty-loosey) then thats going to increase the trigger pressure, perhaps to the point where it wont release.
Maybe the trigger shoe is stopping it from getting to the new break point?

Dodgy situation now...pellet/pellets up the spout and trigger jammed.
Ideally you need to apply the safety -lock the bolt back and clear the barrel.

errrr....its a three handed job to.....
hold bolt  in cocked but not locked back (down) position
screw in adjuster
and pull trigger.

without putting a hole in wall/ceiling /window
Squeaky bum time agreed mate .Something tells me it's a bit more in-depth than mere adjustment as it worked fine yesterday .
Title: Re: Re non firing
Post by: Foxdropper on August 11, 2021, 09:36:26 PM
Quote from: KevG on August 11, 2021, 09:28:36 PM
the mk1 gamo can have alot of travel.if your brake point is far back the trigger shoe could be causing the problem like Stuart has already said
KevG
We have a winner 🤪😇😄😩😁😀🤭🤓🙄
Shoe off and now fires .How strange it fired perfect yesterday though .Should I be readjusting the screw back of trigger before using again .Back to where it was ?
Many thanks Kev and others .
Title: Re: Re non firing
Post by: KevG on August 11, 2021, 09:39:52 PM
those trigger shoes can move out of adjustment.thats what will have happend.the trigger can be moded to shorten first stage travel. you can adjust but not by much with the rear grub screw
KevG
Title: Re: Re non firing
Post by: Foxdropper on August 11, 2021, 09:44:34 PM
So by tightening it clockwise to a point it will lengthen the pull before triggering is that right ?
Or will it lessen the crepe ?
Tomorrow's job anyway I'm off to bed ,early start .Many thanks lads ,thought I'd bought a right dead ender 🤣
Title: Re: Re non firing
Post by: Foxdropper on August 11, 2021, 09:46:34 PM
Next issue is the mags .Can they be refurbed or do I need new .On net theres 12 shot copies.Will they fit the mk 1 please ?
Title: Re: Re non firing
Post by: KevG on August 11, 2021, 09:55:02 PM
yes 12 shot mags will fit.but rapids being rapids you may need to adjust the barrel position slightly.
KevG
Title: Re: Re non firing
Post by: Squinty on August 11, 2021, 10:20:37 PM
Quote from: Foxdropper on August 11, 2021, 09:44:34 PM
So by tightening it clockwise to a point it will lengthen the pull before triggering is that right ?
Or will it lessen the crepe ?
Tomorrow's job anyway I'm off to bed ,early start .Many thanks lads ,thought I'd bought a right dead ender 🤣

the theoben sporter instructions are a bit arse backwards, they state

Screw out for more
engagement using
a 1.5mm allen key
- ¼ turn at a time.

So screwing in gives less sear engagement .....a 'lighter trigger.' .basically shortens the last bit of the long pull.
Everything to that point is the spring
Title: Re: Re non firing
Post by: Squinty on August 11, 2021, 10:31:31 PM
(https://i.imgur.com/CmYxRJH.jpg)

15 L...(fat trigger pin) is responsible for the long travel , its miles from the bottom sear 15 E(strut)

its a lightly modified £10 unit from the ilke of Gamo Hunter and other basic springers.
Title: Re: Re non firing
Post by: Foxdropper on August 12, 2021, 03:34:28 PM
Thankyou all for the input chaps 👍🏻👍🏻
Title: Re: Re non firing
Post by: Kernal on August 12, 2021, 03:35:46 PM
Quote from: Foxdropper on August 12, 2021, 03:34:28 PM
Thankyou all for the input chaps 👍🏻👍🏻

Did it get sorted M8,

:)
Title: Re: Re non firing
Post by: KevG on August 12, 2021, 07:12:46 PM
yes m8 problem solved
KevG
Title: Re: Re non firing
Post by: Foxdropper on August 12, 2021, 08:44:31 PM
Again thanks lads for taking the time last night .👍🏻