Theoben Rapid Forum

Theoben General Chat Area => Theoben Rapid Discussion => Topic started by: Foxdropper on July 26, 2021, 09:54:04 PM

Title: New to rapids
Post by: Foxdropper on July 26, 2021, 09:54:04 PM
Hi all .
I'm about to buy my first rapid mk 1 .
Had airgun all my life but never the chance of a rapid appeared until now .It's fac ,34 lb and I've a slot waiting to fill on fac license .My reason for posting and asking is this .Is there anyone in the Wiltshire area who would be willing to have a look over the gun once bought as it appears rather cheap at £350 .00
It's from Sussex and getting rfd to my rfd to collect .
It's getting a new seal kit on top of price .
I'd also like a recommended pellet in .22 and advice on where to buy a fill probe as it's dosnt come with one apparently .I've a dive bottle for the hw100 and hoping it can be filled from that .
Will be used on rabbits and corvids just out of reach  of the 100.
Hopefully someone nearby will set my mind at ease and maybe point me in the direction of a few upgrades .
Regards FD
Title: Re: New to rapids
Post by: KCE on July 26, 2021, 10:06:14 PM
That is cheap for a tyro stock even FAC.
FAC do tend to sell for less than sub 12 for some reason.
That is a very good buy at that price.

Im sure some one on here will be along to help you regarding a hose or even think about a quick fill from Dr Bob on here.

Regards Kev.
Title: Re: New to rapids
Post by: Foxdropper on July 27, 2021, 06:39:15 AM
I have the hose sorry just not the correct end for bottle .
Title: Re: New to rapids
Post by: nevadacowboy on July 27, 2021, 09:03:07 AM
Adapters are available from best fittings to enable you to fill the buddy bottle direct from your dive cylinder without using the whip. Depending on your dive cylinder type you may already have one attached to your whip where it connects to the dive cylinder.
iirc it is a din fitting you require.
Title: Re: New to rapids
Post by: Foxdropper on July 27, 2021, 04:08:57 PM
This is what I have already 👍🏻
Title: Re: New to rapids
Post by: nevadacowboy on July 27, 2021, 06:46:44 PM
If you unscrew your whip from the knurled adapter then you should be able to screw your buddy bottle in where you removed the whip. You will need to purchase a small delrin seal from best fittings that will go inside the adapter prior to fitting the buddy bottle.
Title: Re: New to rapids
Post by: Ca_Varminter on July 27, 2021, 08:35:10 PM
Quote from: nevadacowboy on July 27, 2021, 06:46:44 PM
If you unscrew your whip from the knurled adapter then you should be able to screw your buddy bottle in where you removed the whip. You will need to purchase a small delrin seal from best fittings that will go inside the adapter prior to fitting the buddy bottle.
Well you guys are on the right track.
But it may not be that easy!!
The fill adapter like you are talking about has an internal shelf for the Delrin insert to butt up against!
You may need a buddy with a lathe make a custom Delrin insert,
long enough to slide all the down till it bottoms out...

It may be easie just to get an bottle adapter that will screw on to the end of your hose from Best Fitting....

(https://photos.imageevent.com/scl_electronics/gun/air/rapid%20insert.jpg)

Stuart


Title: Re: New to rapids
Post by: KevG on July 27, 2021, 10:34:58 PM
like already said just remove whip from the first adapter that goes into filling bottle.you can just screw buddy bottle into that.if you need a delrin seal I can knock you one up and send it you m8.
KevG
Title: Re: New to rapids
Post by: Foxdropper on July 29, 2021, 04:32:32 PM
Many thanks for the replies lads .I think I'll order a fill end to the probe ,sounds easier .
New seals getting fitted by vendor ,can't wait 👍🏻