Just after a bit of advice,
When I service my mk2 do you think its worth changing the complete exhaust valve for a dr bobs one?
I changed it over when I done my mk1 a couple of months ago.
Is there anything else to do to it whilst I'm at it?
Cheers
i would for peace of mind , nothing more infuriating if it fails and you have t strip the gun again
Very true, for the price of the valve its a no brainer really.
You are on the right Path!
Since you have your MK II Stripped down...
Replace all O-rings..
Then If you want to do a little tuning...
A very slight Polish to the Hammer's bearing area's.
Also you can give a slight polish to the Bolt- Body also.. Makes the action smoother!
(https://photos.imageevent.com/scl_electronics/gun/air/websize/polish.jpg)
Just remember you are wanting a slight polish to these pieces!!
You don't want to remove so much metal, that the parts are Under-Sized!!
Good Luck,
Stuart
if it ain't broke.....
From and Engineer.....
"If it Ain't Broke........Improve It!!!"
Stuart
Don't really want to remove the hammer assembly at the moment. It still has the anti tamper plug fitted. If in the future I have to remove it I will polish the assembly. People have said polish the barrel, with what?
Sometime in the future maybe a polygon barrel.
Thats what I forgot to ask.
When I have to remove the anti tamper plug what do you replace it with.? Is it a screw in plug like the mk1?
I love my.22 polygonal barrel on my Titanium Rapid!
But if your barrel is accurate.. you don't need to mess with it..
But if you have to, any good non-imbedding polish will do...
Since we don't hassle with Anti-Taper over on my side of the pond...
I can't help..
But Dr Bob or KevG should point you in the right direction!!
Good Luck,
Stuart
The accuracy isn't too bad. I've only been able to set up the scope in the back garden @30yards. It puts out half inch groups fairly consistently.
https://www.youtube.com/watch?v=Gkg_2v2X3Ac
i done this so many times now on lots of barrels works a treat i used a cordless drill but always go the same way as the rifling and use the finish paper until all the dirt is completely gone when fin it should be like glass if you look down it (other ways but i prefer this one )
get the 3m polishing paper from ebay
Thanks for that. Never seen barrels being polished.
Was his lathe really on his lawn? ;D
its a mexican thing ;)
Ah, so you have to drink a bottle of tequila at the same time. That'll be interesting ;D
Another thing that I've noticed is that the valve cap isn't a 3/16 key like my mk1. It's 5mm.I knew they had changed the grub screw holding the valve body, all for the better too. Every day is a learning day.
Quote from: williamthedog on June 21, 2021, 11:17:28 AM
Another thing that I've noticed is that the valve cap isn't a 3/16 key like my mk1. It's 5mm.I knew they had changed the grub screw holding the valve body, all for the better too. Every day is a learning day.
I have a mk1 block that came with 5mm hex on both adjuster (M20) and valve cap, a 3/16 key just slips under pressure.
As the gun turned out to be something of a BITSA I figured that they were aftermarket,
Not surprised considering the M20 adjuster but odd to have a mixture of imperial and metric on the valve cap?
I don't think it's been apart before looking at it but you never know. Anti tamper still on the hammer.
Don't get me Wrong I love my Rapid.. if you can't tell..
The One major PIA is why the mix metric with British and SAE....
From Threads sizes to Hex keys!!
You need Two Sets of hex keys to work on your Rapid properly!!
But what is even worst, My Titianium Ul_TI_Mate Rapid...
Chip Smith, Machinist Extraordinaire, creator of my Titanium monster...
He wanted to use "Standard" off the shelf Rapid parts....
So he Machined them with the same threads as the standard Rapid!!!!
Stuart
Good old British engineering
Quote from: williamthedog on June 21, 2021, 03:02:57 PM
Good old British engineering
Ha, Ha, Ha...... ;D ;D ;D ;D ;D ;D ;D ;D ;D ;D ;D
If you call it that......
:-X :-X :-X :-X :-X :-X :-X Shhh... Don't Tell Dr Bob I said that!!!
Stuart
the mk2 gun you have is a right heady mix of things in thread sizes , i have one the same .