Just in the process of sorting out the third instalment on my Rapid feature for AGW.
Using some of Dr Bobs excellent parts for the service, but I would like to high light some of the things people should look out for to check if their gun has received some "unwanted" attention. The gun featured is a MK1.
Now so far from my own gun I have a bottle adaptor, which has been drilled out and shortened, presumably to get a free flow type effect, other than that it's fine.
So looking for a rogues gallery, the thinks I know about are drilled out barrel ports, and I seem to remember being told about people running a drill through the barrel location screw to open the barrel port? Which means they re-tap the location hole to a larger size.
Anything you have seen will be helpful. Will be including reference to this most excellent forum.
you will have to give me a ring pete and can tell you a few things.
KevG
I have one in my collection I'll take some pictures for you.
Bob.
yeah, I bought one of 'those' with an opened up top-transfer port. ::)
Often only a sign of a repair to the 2ba location thread... done properly to mk2 specs.. . no problem.
Thing is externally... without stripping a gun down there's very little to see and asking a seller if you can take his rapid apart is probably a good way to be shown the door.
I think the only way is to put it over a chrono with a full bottle to check consistency and the power curve.
And listen to the shot cycle for pops, farts and twangs.
Well I was properly done up a couple of years ago with a 'cheap rapid'.
The only visual sign although under the front scope mount ... a previous owner had re-threaded the location grub to some obscure pitch and opened up the top-transfer port.
Because the grub was slightly out and the clever person had drilled the front mount to use a wider bolt... the magazine didn't sit flush.. shaving the pellets.
Hadn't even drilled it straight, just catching the edge of the tail o-ring seat. And leaving a burr that stopped the valve from seating.
Said Rapid wouldn't run right with an irregular power curve and odd noises.
Both hammer adjuster and valve caps had been ahem.. modified (with a hammer?) to fit metric hex keys.
A recent 'new valve' was actually an old one with two oversized o-rings and an exhaust spring that could have been taken from a novelty pen.
The hammer spring was similarly weak and the inertia weight with knackered spring was embedded in grease.
The rear trigger boss protruded into the hammer pocket.. and fouled the back edge of the hammer which could have been fixed with washer.
And the pip thread had been stripped so that was held in with red loctite.
The same someone had gone to great trouble polishing and reshaping the trigger sears and bending the sear springs into submission.
Wouldn't have been so bad if the safety didn't have one safe position and two off.. one back and one forward :o :o
The cocking dog fell apart on the first turn of the fixing screw, although that didn't really matter as the head of the metr-inch screw was too long and bound up on the hammer.
Also the probe spring was stronger than the exhaust valve spring :o
The R7 bolt handle thread hadn't been shortened to suit an adjustable bolt which fouled the pin and wound that forwards.
The barrel was OK once re-crowned but who ever had dipped it had made it look like it had a quality deep black ;D
I really wouldn't have guessed until it came off in flakes. :-X
Oh and the buddy bottle.. . FML.
A Bear Divers refurb, with recent test sticker and full of crispy aluminium oxide.
All sorted now, it was that bad I couldn't even bring myself to part it out on the bay.
You really have to bugger up a Rapid so much to call it "scrap" most can be coaxed back to a working life .
atvb' Mick
Thanks for the replies fellas, some "chambers of horror" there as Dr Bob would say!
one thing to look out for when buying a sub 12ftlbs model.and its very easy to spot.when flicking bolt handle back from forward positioni there should be a fair bit of travel of cocking bolt before it picks the hammer up and comes under tension.if it picks hammer up straight away it means the hammer pip as been shortend allowing hammer to rest further forward.this would have been done to mess with power level and would put gun out of ballance for sub 12 ftlbs
KevG
Might have some more material for you once Kev opens up my one soon :D
You should have come over or me popped up when i was fixing one up for Stu James.
It had most certainly been used to play hockey at some point in its life!
Regards,
Rhys
Like this?
Hey Dr B.....
OMG, that Hole is not even centered on the center rib!!!!!
At least when I drill on my Rapid ... the hole are on Center!!!!
(https://photos.imageevent.com/scl_electronics/gun/air/websize/vertcal-ss-tray2.jpg)
(https://photos.imageevent.com/scl_electronics/gun/air/websize/newmounts.jpg)
Stuart
Bloody hell Bob it looks like some one has used a fence post auger on that top hole lol
atvb' Mick
some left the factory that was a mess to.some of the last mk1s had faults that should never be on a gun at that price
KevG
Quote from: Ca_Varminter on March 15, 2021, 04:16:33 PM
(https://photos.imageevent.com/scl_electronics/gun/air/websize/newmounts.jpg)
Stuart
thats what I need doing for my mk2s, even with the scalloped block the damned rail catches my thumb every time
Looking at those pictures, and hearing the stories, makes it difficult to comprehend how people can do such things.
Back in 1995 the Rapid was £595, which in todays money equates to £995, a lot of money which ever way you cut it, yet people are willing to butcher their own guns, or give it to someone with little experience to butcher it for them. Nowt as queer as folk.