Theoben Rapid Forum

Theoben General Chat Area => Theoben Rapid Discussion => Topic started by: nevadacowboy on October 27, 2020, 03:34:20 PM

Title: Refurbishing a buddy bottle
Post by: nevadacowboy on October 27, 2020, 03:34:20 PM
I have just picked up a MFR 280 buddy bottle complete with valve.  It is a bit rough and I would like to take it back to the bare metal and then paint it. What is the best way to remove all the old covering.
Title: Re: Refurbishing a buddy bottle
Post by: Bearded Sniper on October 27, 2020, 03:44:54 PM
They look powdercoated to me, its quite thick when it chips off.
I'd say heat if it was being stripped down, but how much I wouldn't know
Title: Re: Refurbishing a buddy bottle
Post by: Ca_Varminter on October 27, 2020, 05:33:22 PM
Nope....
Take a look at Luxfer's site.
They recommend No baked on finishes!!
It can compromise the the integrity of the Bottle!!
https://www.luxfercylinders.com/support/temperature-exposure (https://www.luxfercylinders.com/support/temperature-exposure)

Stuart
Title: Re: Refurbishing a buddy bottle
Post by: Bearded Sniper on October 27, 2020, 05:51:14 PM
Quote from: Ca_Varminter on October 27, 2020, 05:33:22 PM
Nope....
Take a look at Luxfer's site.
They recommend No baked on finishes!!
It can compromise the the integrity of the Bottle!!
https://www.luxfercylinders.com/support/temperature-exposure (https://www.luxfercylinders.com/support/temperature-exposure)

Stuart
Don't suppose they say what they are coated with then? Is it just paint? I've wondered this myself in the past
Title: Re: Refurbishing a buddy bottle
Post by: Ca_Varminter on October 27, 2020, 10:13:25 PM
My early ball-bearing valve bottles had slight paint runs on them.....
So probably a good Epoxy type of Paint!

Stuart
Title: Re: Refurbishing a buddy bottle
Post by: nevadacowboy on October 27, 2020, 11:06:38 PM
I still want to know the best method to strip a bottle back to the bare ally



Title: Re: Refurbishing a buddy bottle
Post by: Ca_Varminter on October 28, 2020, 02:52:35 AM
Quote from: nevadacowboy on October 27, 2020, 11:06:38 PM
I still want to know the best method to strip a bottle back to the bare ally
Follow my link to Luxfer site....
There is also an article about stripping...
They recommend non-caustic/etching paint remover
https://www.luxfercylinders.com/support/paint-strippers-for-aluminum-cylinders (https://www.luxfercylinders.com/support/paint-strippers-for-aluminum-cylinders)
They also recommend plastic bead blasting.....not glass, oxide, or sand blasting....

Stuart
Title: Re: Refurbishing a buddy bottle
Post by: nevadacowboy on October 28, 2020, 01:59:55 PM
Thanks for the link, tells me what I need to know.
Title: Re: Refurbishing a buddy bottle
Post by: Maxwell on November 04, 2020, 10:47:11 AM
What are you going to use to refinish the bottle are you going to prime it then paint it or powder coat it
Title: Re: Refurbishing a buddy bottle
Post by: nevadacowboy on November 04, 2020, 02:57:07 PM
I have rubbed it down and painted it with auto spray paint. It has given me an acceptable finish.
Title: Re: Refurbishing a buddy bottle
Post by: Daztilley on November 04, 2020, 04:32:33 PM
Thats what I normally do mate - using satin black spray paint 👍

Looks good if you make sure not to get any runs in the paint
Title: Re: Refurbishing a buddy bottle
Post by: Maxwell on November 17, 2020, 05:36:54 PM
Do you etch primer the bottle first
Title: Re: Refurbishing a buddy bottle
Post by: Ca_Varminter on November 17, 2020, 05:41:23 PM
As above about Stripping the Paint...
Non-etching Primer is Strongly recommended

Stuart