Theoben Rapid Forum

Theoben General Chat Area => Theoben Rapid Discussion => Topic started by: smithy123 on October 23, 2020, 05:47:04 PM

Title: Post for kevg
Post by: smithy123 on October 23, 2020, 05:47:04 PM
I've just took my mod off and this is how it's been threaded, is this fine or will your mod not fit?? I've ordered a carbon shroud to sleeve my barrel as I wanted to get a carbon mod to go with with it.

Thanks
Title: Re: Post for kevg
Post by: Ca_Varminter on October 23, 2020, 06:13:20 PM
How is it shooting?
Good Accuracy??
If you want some improvement, a good crown would help...
I am sure KevG can machine his mod to work...
Or may want to cut, re-thread and crown the barrel!!
This will eliminate any question of alignment and ensure the best accuracy!!

But this is KevG's call.. and also has the ability to have a hand-on inspection!!

Good Luck,
Don't let Kernal...touch it!!!
::) ::) ::) ::) ::) ::)
(https://photos.imageevent.com/scl_electronics/misc/mages/dead%20mouse.gif)

Stuart
Title: Re: Post for kevg
Post by: Buzz20 on October 23, 2020, 07:48:01 PM
KEV's your man fella
Top fella and top work
🐝
Title: Re: Post for kevg
Post by: Kernal on October 23, 2020, 08:02:37 PM
LOL,...Don`t let Kernal touch it....  ;D ;D

I have that much going on,..I don`t have time for anything else Stuart,...

:)
Title: Re: Post for kevg
Post by: Kernal on October 23, 2020, 08:06:15 PM
Quote from: Kernal on October 23, 2020, 08:02:37 PM
LOL,...Don`t let Kernal touch it....  ;D ;D

I have that much going on,..I don`t have time for anything else Stuart,...

:)

P:s  i need a new keyboard,...its playing up big time with my mouse,.... :(
Title: Re: Post for kevg
Post by: smithy123 on October 23, 2020, 08:56:37 PM
Quote from: Ca_Varminter on October 23, 2020, 06:13:20 PM
How is it shooting?
Good Accuracy??
If you want some improvement, a good crown would help...
I am sure KevG can machine his mod to work...
Or may want to cut, re-thread and crown the barrel!!


This will eliminate any question of alignment and ensure the best accuracy!!

But this is KevG's call.. and also has the ability to have a hand-on inspection!!

Good Luck,
Don't let Kernal...touch it!!!
::) ::) ::) ::) ::) ::)
(https://photos.imageevent.com/scl_electronics/misc/mages/dead%20mouse.gif)

Stuart




It's accuracy is Bob on I it's putting pellet on pellet I was just making sure that it had been threaded right as kernel pulled a face to it lol😂😂 but I've messaged Kev to make a carbon mod for me. But when kernal pulled his face at it I questioned my self weather or not it's would fit straight on
Title: Re: Post for kevg
Post by: smithy123 on October 23, 2020, 09:00:26 PM
Also how can you cut any more barrel away it's only a 16" as it is. Where would I buy a 19" barrel from can anyone recommend somewhere

Thanks
Title: Re: Post for kevg
Post by: Ca_Varminter on October 23, 2020, 09:06:26 PM
Quote from: Kernal on October 23, 2020, 08:06:15 PM

P:s  i need a new keyboard,...its playing up big time with my mouse,.... :(

I think I found the problem with your Mouse... Maybe your Keyboard is having the same problem!

(https://media.giphy.com/media/SDkwQeppxqUMw/giphy.gif)

;D ;D ;D ;D ;D ;D ;D ;D

Stuart
Title: Re: Post for kevg
Post by: Ca_Varminter on October 23, 2020, 09:10:16 PM
Quote from: smithy123 on October 23, 2020, 09:00:26 PM
Also how can you cut any more barrel away it's only a 16" as it is. Where would I buy a 19" barrel from can anyone recommend somewhere

Thanks
Well Let's not toss anything out Too Fast!!
Let's give KevG a chance to look at the barrel!
If she is stacking pellets on top of each other.... let keep our fingers crossed the threading is straight!!

Good Luck,
Stuart
Title: Re: Post for kevg
Post by: smithy123 on October 23, 2020, 09:16:57 PM
I hate waiting that's the problem, I'm so inpatient 😂😂 and we can't go to Yorkshire to get the jobs done what I need which is really frustrating!!!

Need a silent hammer pip doing, new mod made and fitted, full Kevg service the list is endless!!

Dear do this hobbie lol 😂

Brad
Title: Re: Post for kevg
Post by: Ca_Varminter on October 23, 2020, 09:46:58 PM
Well you may need to do what we do over on this side of the Pond!
Get a Lathe... and Mill.....learn how to operate them safely!!
Then Cut, Thread Turn down, and mill, your Own parts out ....
Also you can do your own tuning!!!!
(https://photos.imageevent.com/scl_electronics/gun/ultimaterapid/websize/ti-pip1.jpg)

And sit a listen and watch KevG for a couple of days!!!
(I am an engineer(electronics), work with a gunsmith/friend when I graduated...So I learned a lot machining!)

So learn to do it yourself!!

Stuart
Title: Re: Post for kevg
Post by: Kernal on October 23, 2020, 10:10:50 PM
Or even better and cheaper get KevG to do it LOL,....What you like!

:)
Title: Re: Post for kevg
Post by: smithy123 on October 24, 2020, 10:42:51 AM
That a good idea kernal😂 I'll just wait lol
Title: Re: Post for kevg
Post by: nevadacowboy on October 24, 2020, 01:17:35 PM
If you cannot get to Kev G's personally you could always send the action by post to him to have the work done.
Title: Re: Post for kevg
Post by: KevG on October 24, 2020, 02:31:04 PM
if its accurate I would leave it.main thing is the threading as been done true to the bore and its nice and true were the silencer buts up to the barrel,otherwise it can force the silencer out of line.it would not be as quiet as normal as the barrel is going to extend further into the silencer
KevG
Title: Re: Post for kevg
Post by: smithy123 on October 24, 2020, 02:47:00 PM
Quote from: KevG on October 24, 2020, 02:31:04 PM
if its accurate I would leave it.main thing is the threading as been done true to the bore and its nice and true were the silencer buts up to the barrel,otherwise it can force the silencer out of line.it would not be as quiet as normal as the barrel is going to extend further into the silencer
KevG

I'll leave it then... I've just carbon wrapped my buddy bottle and my mod and on Monday my carbon tube should be here for my barrel

He's a pic of what I've just done !!!!
Title: Re: Post for kevg
Post by: KevG on October 24, 2020, 08:11:38 PM
that looks OK.just need to carbon tube now to sleve barrel
KevG